758293
11
Zoom out
Zoom in
Previous page
1/26
Next page
9
English
3. Make sure that the vehicle has the neg-
ative pole on the ground (see manual of

4. Make sure the device is turned off.
5. Make sure that the ignition key is set to
“OFF/OFF. For keyless systems, make
sure that the ignition is turned off com-
pletely before connecting the mobile
power station.
6. Apply the parking brake or parking
brake of the vehicle. (On vehicles with
manual transmission, set the shift lever
to the neutral position.) On vehicles with
automatic transmission, set the lever to
the “P” position).
7. Plug the starter cable (A) into the corre-
sponding socket (8).
8. For vehicles with the negative pole to
ground, connect the red battery termi-
nal Plus to the positive pole of the vehi-
cle battery.
9. Now connect the black battery terminal
Minus only to a grounded point on the
vehicle (e.g. on the engine, chassis or
other grounded location on the vehicle).
10. Turn on the device with the ON/OFF
switch (2).
11. Press the start button (3). The device

seconds. The display (6) shows “OK”.
12. If the vehicle battery is so weak that the
pilot light does not illuminate, wait
about 15 minutes before attempting to
start the engine.
13. Now start the engine. The start attempt
must not take longer than 15 seconds.
Take a break of at least one minute after
each start attempt.
14. As soon as the engine starts, switch off
the device with the ON/OFF switch (2).
15. First remove the black battery terminal
Minus and then the red battery terminal
Plus. When removing the battery termi-
nals, make sure that the cables do not
come into contact with rotating parts of
the motor.
16. Remove the starter cable from the
device.
17. After successfully starting the engine,
wait until it runs smoothly.
12. Jump Start – Special Procedure
with negatively earthed Battery
Older vehicles can still have the positive
pole at the mass.
When starting a vehicle with a negatively
earthed battery, follow the
steps 1 – 7 in chapter Jump Start - Stand-
ard Procedure.
8. First connect the black battery terminal
Minus to the negative pole.
9. Now connect the red battery terminal
Plus to the frame of the vehicle.
Then follow the steps 10 – 17, as described
in the chapter Jump Start – Standard
Procedure.
13. Operating the Compressor
The compressor of the device generates
during operation loud noises that can dam-
age the hearing. Wear ear protection while
operation.
1. Unwind the air hose (14) completely and


2. Use an adapter from the adapter set (B).
3. Open the lever (15), insert the valve plug
(16) onto the valve and push the lever
down.
4. Turn on the device with the ON/OFF

decrease) the air pressure, depress and
hold the buttons (9/10) for at least 5
seconds. To increase the air pressure,
press the plus button (10). To decrease
the air pressure, press the minus

5. To turn on the compressor, press the
compressor button (11). The compres-
sor starts audibly and begins to pump.
6. To turn off the compressor, press the
button (11) again.
7. Open the lever and remove the valve

8. If necessary, check the new air pressure

manometer.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia BT-JS001 - 7063516 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-JS001 - 7063516 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info