758282

Batavia BT-CT001 - 7063419 Manual

12
Zoom out
Zoom in
Previous page
1/46
Next page
English
10
12.3 Assembling a cutting / sanding disc
(See g. C)
Unscrew the small screw (a) on top of man-
drel, then insert an appropriate cutting/
sanding disc into mandrel and lightly tighten
(a) with wrench. Do not
over-tighten, or the cutting/ sanding disc
may crack.
12.4 Assembling felt wheel or tip
(See g. D)
The felt wheel or tip should be screwed on
the mandrel.
12.5 Assembling a sanding drum
(See g. E)

(a) on top of the sanding drum
shank. Slide the sanding drum onto the
(a)
again.
12.6 Installation of auxiliary handle
You can use the machine with or without
auxiliary handle. Therefore, use proper
guard (3)
Depending on the work ahead it is recom-
mended to use auxiliary handle and hold the
machine with both hands.
Disconnect the power tool from power
supply.
• Unscrew and remove the guard (3).
• Put auxiliary handle (1) on the machine.
• Install and tighten appropriate guard
(3).
12.7 Installation of exible shaft
Before assembly always remove
the plug from the mains!
• Loosen and remove front plastic guard
(3) (g. G).
• Pull some of the cord (a) (g. H) from
(11) so its end can be
installed in the collet nut (b) (g. H).
• Press and hold spindle lock button (4).
• Tighten the collet nut (2) with the sup-
plied wrench.
• 
shaft (11).
• 
the positioning nut (g. I).
12.8 Installation and replacement of acces-
sories in exible shaft holder
(g. F)
Before assembly always remove
the plug from the mains!
• 

shaft spindle locking.
• (a).
• Insert the accessory into the collet that
matches the shank size of the
accessory.
• Tighten the collet nut (a) with the sup-
plied wrench.
• 
spindle locking (b).
13. Switch on/off
To turn on the machine, press the “I” side of
the ON/OFF switch (9). To turn off the
machine, press the “0” side of the ON/OFF
switch(9).
14. Speed setting
The tool has a variable speed selector (6)
for precise speed adjustment numbered “8”
to “35”. The speed can be adjusted from
8,000 to 35,000 min-1.
Always choose the correct speed range for
your work according to the material.
Determine the correct speed for work on
any material by practicing on a piece of
scrap.
14.1 Adjustment of the speed
• After setting the switch (9) position to ‘I’
you can change spindle rotational
speed by choosing appropriate number
shown on the display (6) range from 8
to 35.
• You can change rotational speed by
(7).
• Press the button ‘+’ (many times if
needed) to increase speed.
• 
needed) to decrease speed.
Choose a low speed when working with
wood, plastics and polishing.
7062854-Compact-Tool-170W-Ma-1803-27.indb 10 14-05-18 10:20
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Batavia BT-CT001 - 7063419 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-CT001 - 7063419 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info