Manual Batavia BT-CT001 - 7063419 (page 9 of 46) (English, German, Dutch, French)

758282

Zoom out

Zoom in

1/46

English

sory may contact hidden wiring or its

own cord. Cutting accessory contact-

ing a “live” wire may make exposed

metal parts of the power tool “live” and

could give the operator an electric

shock.

k. Always hold the tool rmly in your

hand(s) during the start-up. The reac-

tion torque of the motor, as it acceler-

ates to full speed, can cause the tool to

twist.

l. Use clamps to support workpiece

whenever practical. Never hold a small

workpiece in one hand and the tool in

the other hand while in use. Clamping

a small workpiece allows you to use

your hand(s) to control the tool. Round

material such as dowel rods, pipes or

tubing have a tendency to roll while

being cut and may cause the bit to bind

or jump toward you.

m. Position the cord clear of the spinning

accessory. If you lose control, the cord

may be cut or snagged and your hand

or arm may be pulled into the spinning

accessory.

n. Never lay the power tool down until the

accessory has come to a complete

stop. The spinning accessory may grab

the surface and pull the power tool out

of your control.

o. After changing the bits or making any

adjustments, make sure the collet nut,

chuck or any other adjustment devices

are securely tightened. Loose adjust-

ment devices can unexpectedly shift,

causing loss of control, loose rotating

components will be violently thrown.

p. Do not run the power tool while carry-

ing it at your side. Accidental contact

with the spinning accessory could snag

your clothing, pulling the accessory into

your body.

q. Regularly clean the power tool’s air

vents. The motor’s fan will draw the

dust inside the housing and excessive

accumulation of powdered metal may

cause electrical hazards.

r. Do not operate the power tool near

ammable materials. Sparks could

ignite these materials.

s. Do not use accessories that require

liquid coolants. Using water or other

liquid coolants may result in electrocu-

tion or shock.

4. Kickback and related warnings

Kickback is the sudden reaction of a

wedged or locked spinning attachment

such as a grinding or sanding disc or a wire

brush etc. This causes the spinning attach-

ment to come to a sudden stop, which will

force the electric tool against the rotating

direction of the attachment.

If, for instance, a cutting disc becomes

locked or jammed in the work piece, the

edge of the disc may fracture inside the

work piece and cause a violent kickback.

The disc will then move away from or

towards the operator, depending on the

direction of rotation on the locking point.

This may also shatter the disc.

Kickback is caused by wrong or inappropri-

ate use of the tool and can be avoided by

following the safety advice below.

a. Hold the electric tool tightly with both

hands and assume a position, in which

you can compensate a kickback. If

present, use the accessory handle to

be able to control kickback and coun-

termovement of the running motor.

With the necessary precautions the

operator can control all forces of kick-

back and countermovement.

b. Keep your hand away from the spin-

ning attachment. A kickback can throw

the attachment onto your hand.

c. Keep your body out of the area into

which the tool is thrown by a kickback.

The tool is thrown into the direction

reverse to the direction of the disc at the

locking point.

d. Use extreme care when working

around edges or sharp corners. Make

sure the attachment cannot become

locked into or bounce back from the

work piece. Rotating discs tend to lock

into or bounce back from edges and

7062854-Compact-Tool-170W-Ma-1803-27.indb 7 14-05-18 10:20

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Batavia BT-CT001 - 7063419 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Batavia BT-CT001 - 7063419 Manual

Product: