515892

Basetech 86 delige set Manual

11
Zoom out
Zoom in
Previous page
1/25
Next page
20
21
Outside diameter and thickness of a insert tool must correspond to the dimensions specified
for your power tool (Ø<25 mm). Incorrectly dimensioned insert tools may not be adequately
shielded or controlled.
Tools or external accessories must match; otherwise, the result may be imbalanced operation,
vibrations, etc.
Do not use any damaged tools. Perform an inspection before each use: for example, check
grinding wheels for cracks, cutting disks for cracks, heavy wear.
Never set aside the power tool before the insert tool has come to a complete standstill. The
rotating insert tool can come into contact with the surface upon which it is placed. This can
result in your losing control of the power tool.
Do not operate the power tool while walking. Your clothing can get caught in the rotating insert
tool due to accidental contact, and the insert tool can puncture your body.
Do not use the power tool near flammable substances. Sparks can cause these materials to
ignite.
Hold the unit firmly during every use so that you may be adequately prepared to react to recoil.
Recoil can result in minor or severe injuries. Ensure the safe and even guiding of the tool during
work in order to avoid recoil.
Users of the device should be at least 16 years old.
Avoid freehand grinding without a hand rest. Ensure a stable stance or support of your hand
and arm.
Do not use any cracked, bent, imbalanced or vibrating cutting disks, grinding wheels or grinding
pencils.
Always select the tool best suited for the particular operation. Cutting disks, for example, must
not be used for side grinding.
Before each use of each tool you should ensure that:
it is assembled and tightened properly.
the device rotates freely (rotate by hand to check).
a test run has been performed by running the tool from a safe position for approximately one
minute at the highest speed and while not subjected to any stress.
Flying sparks when working with metal can result in burns. Keep your work area free of
flammable substances.
When working, wear goggles, hearing protection as well as a dust mask. It is recommended
that you wear an apron as well as protective shoes where possible.
Do not wear any jewelry when working.
Tie up hair or loose clothing in the proper fashion so that they do not get caught in rotating
parts.
•
•
•
•
•
•
•
•
•
•
•
•
-
-
-
•
•
•
•
4. Operation
A) Tool attachment
Choose the proper tool for the operation and the proper collet chuck.
Assemble the cutting disks, polishing disks and grinding attachments to their accompanying
holders.
Press in the latch button on the shaft end of the device to lock the shaft in place. Unscrew
the knurled nut, insert the proper collet chuck into the slot and gently screw the knurled nut
back on.
Insert the shaft of the selected tool into the collet chuck and tighten all parts using a matching
open-end wrench so that they do not slip.
The procedure when using the tool fitting on the flexible shaft is the same; however,
the shaft is locked in by inserting the stop key in the hole provided.
It is recommended that the device be disconnected from the power supply each time
you change the tool in order to avoid injuries resulting from accidentally activating
the ON/OFF switch.
B) Assembling the flexible shaft
Select a collet chuck custom-fit to receive the square end of the flexible shaft.
Press in the latch button on the shaft end of the device to lock the shaft in place for the following
operation.
Unscrew the knurled nut.
Remove the plastic lock bush on the shaft end of the device housing.
Gently pull out the flexible shaft from the covering and insert the collet chuck 3-5 cm on the
square end and push both into the slot.
Tighten the flexible shaft with the lock bush on the threading on the device casing.
Tools are installed in the tool attachment slot of the shaft as described above.
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Basetech 86 delige set at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Basetech 86 delige set in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info