616233

Barbecook Spring 330 Manual

9
Zoom out
Zoom in
Previous page
1/346
Next page
www.barbecook.com 9
• If the regulator has a screw thread, screw the regulator
counter-clockwise on the cylinder (D).
6.5 Replacing the cylinder
1 Close the gas supply and set all control knobs to OFF.
2 Disconnect the empty cylinder and connect the full cylinder.
3 Check the cylinder, the hose and all gas connections for
leaks. See “7 Checking for gas leaks”.
7 CHECKING FOR GAS LEAKS
7.1 Why check for gas leaks?
Propane and butane are heavier than air. As a result, they do not
float away when leaking from the appliance. Especially on
windless days, a leak can cause the gas to collect in and around
the appliance. That accumulated gas can then ignite and
explode.
7.2 When check for gas leaks?
• Before the first use or before the first use after a long period
of non-use.
1
Also check for gas leaks if your appliance was assembled
by your dealer.
• Each time you replace a gas component.
• At least once a year, preferably at the beginning of the
season.
7.3 Safety instructions
• Put the appliance outdoors, in a well-ventilated area. Make
sure there are no flames or heat sources near the appliance.
• Never use a lighter or match to check for gas leaks.
• Do not smoke and do not light the burners when checking
for gas leaks.
7.4 Which materials do I need?
To check for gas leaks, you need:
• A testing liquid. You can use a ready-made leak spray or a
mixture of water (50%) and dish-washing soap (50%).
• The leak test tool that came with your appliance. You use it
to suck up the testing liquid and apply it to the gas
component or connection that you want to check.
7.5 To check for gas leaks
You check for gas leaks by applying a testing liquid to all gas
components and connections. If the bubbles on a particular
component or connection grow, there is gas leak:
To check for gas leaks, proceed as follows:
1 Put the appliance outside.
2 Get your leak test tool and testing liquid (leak spray or
water/soap mixture).
3 Open the lid and set all control knobs to OFF.
4 Open the gas supply slightly. Turn the valve of the gas
cylinder only once.
5 Suck up some testing liquid with the leak test tool and apply
it to the area that you want to check. You have to check:
• The welds of the gas cylinder (A)
• The hose (B)
• The connections between the cylinder and the pressure
regulator and between the pressure regulator and the
hose (C)
• The connection between the hose and the appliance (D)
0
Your pressure regulator and coupling may be different
from the ones in the illustrations.
6 Do one of the following:
• If you detect a leak, continue as described in “ In case of
a gas leak”.
• If there are no leaks, close the gas supply, rinse all
components thoroughly with water and dry them well.
7.6 In case of a gas leak
1 Close the gas supply and do one of the following:
• If you detected a leak on one of the connections, tighten
that connection.
C D
✔✖
A
C D
B
!gas_spring_standard.book Page 9 Tuesday, July 29, 2014 2:49 PM
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Barbecook Spring 330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Barbecook Spring 330 in the language / languages: All languages as an attachment in your email.

The manual is 61,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info