658717
33
Zoom out
Zoom in
Previous page
1/102
Next page
31
GPS input
gps1.d; gps2.d
The gpsX.d les dene the inputs of GPS units and the location of the antenna relative to the bow of the yacht.
An example of a GPS conguration le is shown below:
Channel 1
Device 1
Com 1 RS232 19200 N 8 1
Offset 0.0
Bow 55.0
COG 100 null.cal null.l null.alm
SOG 101 null.cal null.l null.alm
QHD 102 null.cal null.l null.alm
SVA 103 null.cal null.l null.alm
UTC 104 null.cal null.l null.alm
Line 1 denes the CAN Channel the module is connected to.
Line 2 denes the Device ID of the Module (NOTE: this is set via the DIP switch inside the module).
Line 3 denes the COM port settings:
COM Port COM port used [1 or 2]
Hardware Type Hardware settings for the type of data [RS232, RS485, RS422, NMEA0183]
Baud Rate Baud Rate setting to suit the input [4800, 9600, 19200, 28800, 38400, 57600, 115200]
Parity Parity setting to suit the input[N = no parity]
Data Bits To suit the input [7 or 8]
Stop Bits To suit the input [1 or 2]
Compass Type Identies special compass types (see compatible compass types)
Line 4 denes the GPS antenna position:
Oset GPS Antenna oset from centreline ( - Port, + Starboard) in feet
Bow to GPS GPS Antenna distance from Bow in feet
The additional lines dene the variables. Normally this should not be changed though, for example, you may
wish to add a link to a lter le for SOG:
Variable Name Name of the variable, for user information only]
COM Port Same port as line 3 (above)
Variable Number Variable number where data is stored (from bg_vars.d)
Calibration File Filename of the calibration le to use
Filter File Filename of the lter/damping le to use
Alarm File Filename of the alarm le to use [optional]
Note: For NMEA0183 GPS inputs the preferred inputs are as follows:
Position: GGA, GLL (If GGA or GLL is not available then RMC can be used for Position, in this case VTG must be disabled.)
Velocity: VTG
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BandG WTP3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BandG WTP3 in the language / languages: English as an attachment in your email.

The manual is 7,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info