784763
12
Zoom out
Zoom in
Previous page
1/28
Next page
Manufactured under one or more of these patents.
U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2, Canadian Patent: 2342614,
Australian patent: 2373248 other patents both foreign and domesc applied for and pending. All material copyright of Balboa Water Group.
42281_A | Compable with SpaTouch 1 & 2 12 03.17
The Settings Screen
Priming the Pumps
Exiting Priming Mode
As soon as the Priming Mode screeen appears on the panel,
select the “Jets 1” button once to start Pump 1 in low-speed
and then again to switch to high-speed. Also, select the other
pumps, to turn them on. The pumps should be running in high-
speed to facilitate priming. If the pumps have not primed after
2 minutes, and water is not flowing from the jets in the spa,
do not allow the pumps to continue to run. Turn off the pumps
and repeat the process. Note: Turning the power off and back
on again will initiate a new pump priming session. Sometimes
momentarily turning the pump off and on will help it to prime.
Do not do this more than 5 times. If the pump(s) will not prime,
shut off the power to the spa and call for service.
Important: A pump should not be allowed to run without priming for more than 2 minutes. Under NO circumstances should a pump
be allowed to run without priming beyond the end of the 4-5 minute priming mode. Doing so may cause damage to the pump and
cause the system to energize the heater and go into an overheat condition.
The system will automatically enter the normal heating and filtering at the end of the priming mode, which lasts 4-5 minutes.
You can manually exit Priming Mode by pressing the “Back” button on the
Priming Mode Screen. Note that if you do not manually exit the priming
mode as described above, the priming mode will be automatically terminated
after 4-5 minutes. Be sure that the pump(s) have been primed by this time.
Once the system has exited Priming Mode, the top-side panel will display the Main Screen, but the display will not show the water
temperature yet, as shown below. This is because the system requires approximately 1 minute of water flowing through the heat-
er to determine the water temperature and display it.
*M0XX is a Message Code.
– – – –
°F – – – –°C
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Balboa SpaTouch2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Balboa SpaTouch2 in the language / languages: English as an attachment in your email.

The manual is 2.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info