Manual Babymoov Expert II (page 9 of 36) (English, German, Dutch, French, Italian, Portuguese, Spanish)

496289

Zoom out

Zoom in

1/36

N.B.: Please set the range check function to OFF for normal baby monitor operation or otherwise the

communication range between transmitter and receiver will become very short.

2. The sensor inside the unit will detect the baby’s room temperature and its current reading is shown on

the LCD screen of both transmitter as well as receiver. The normal operating range of the temperature

sensor is -9°C to +50°C . Temperature outside this range will also be shown in the LCD screen except

with less accuracy. In case there is a sudden tempaerature change (eg. you bring the transmismitter

from indoor to outdoor during winter time), the sensor may need to take a few minutes before it can

settle to the new envoiroment and show the correct reading on the LCD screen.

3. When the power ON/OFF switch (1) is set at ON position, a momentarily press of the mode button (3)

will cause the LCD screen to show the different settings in a cyclic order. A screen showing operating

channel/digital code, output power setting, out-ofrange alert setting or range setting will automatically

return to screen showing baby’s room temperature after 5 seconds if no further button is pressed.

BABYPHONE EXPERT II • Instruction Manual

8. The night light (4) can be set permanently ON by moving the power ON/OFF switch (1) to position,

the night light icon will be shown in the LCD. The night light can also be set to be VOX (voice

activated) by momentarily pressing the mode button (3) , the VOX icon will be shown besides the

icon. Under VOX mode, the night light will be switched on once the microphone (5) detects a sound

and automatically goes off a few seconds after the microphone (5) stops picking up any sound.

Momentarily press of the mode button (3) will cause the night light to toggle between permanent ON

and VOX.

9. The condition of the battery is shown by the battery status indicator . When the battery power is

being consumed, the segments within the battery status indicator gradually falls. Once the indicator

becomes empty, it will start flashing, besides, the transmitter will also send out a signal to the receiver

to alert the parents.

10. Each time a button is pressed, a beep tone will be heard to validate your entry being recognized by

the unit.

4. Place the transmitter about 1 m from the crib with the microphone (5) facing towardsthe baby.

5. Adjust the microphone sensitivity using the up/down button (2) such that the unit will be set to transmit

whenever the microphone (5) picks up a sound at your desirable loudness level. The microphone

sensitivity bar graph in the LCD will also change correspondingly. More segment of bar graph shown

means the unit is more sensitive to sound.

6. Once the unit is in transmit mode, the LCD will be backlighted and the transmit icon will be shown.

The transmitter will return to standby mode a few seconds after the microphone (5) stops picking up

any sound and the transmit icon goes off. The LCD backlight will also go off to save battery power.

7. When the Out-of-range alert function is set to On, the transmitter will transmit a signal to the receiver

at regular intervals even when the microphone (5) does not pick up any sound. The transmit icon

will blink correspondingly in the LCD.

RECEIVER

1. Setting of channel, digital code, upper/lower temperature limit and Out-of-range

alert function.

1. a. Set the power ON/OFF switch (8) to ON position to turn on the unit. The LCD screen

will show up and become backlighted. Press and hold mode button (10) for at least

5 seconds to enter into programming mode. A confirmation beep tone will be

heard once the unit goes into programming mode successfully and the LCD wil

show following:

▼ Flashing

▼ Light up steadily

1. b. Use Up/Down button (9) to select a channel same as the transmitter. Each press

of the button will cause the channel no. to advance or retreat one step. Press and

hold the Up or Down button (9) will cause the channel no. to scroll up or down

rapidly. Confirm your selection by pressing the mode button (10). The LCD will show

following:

1. c. Now select the same digital code as the transmitter using the Up/Down button (9).

Each press of the button will cause the digital code to advance or retreat one step.

Press and hold the Up or Down button (9) will cause the digital code to scroll up or

down rapidly. Confirm your selection by pressing the mode button (10). The LCD will

show following :

1. d. Now select the same setting for Out-of-range alert function as per the transmitter

using Up/Down button (9). If a different setting is selected, either false alarm will

be heard or no alarm will be provided even when receiver falls beyond the

communication range of transmitter. Confirm your selection by pressing the mode

button (10). The LCD will show following:

N.B. In case the transmitter is set to operate with range check function, the reciever will

automatically enters range check mode no matter the out-of-range setting is ON or OFF.

Out-of-range alert function

is enabled

CH2 and digital code 28

is selected

High output power is selected

Current baby's room temperature is 23°C

BBPhone Expert II-Notice 5/12/06 11:41 Page 17

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Babymoov Expert II in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Babymoov Expert II Manual

Product: