661218

Baby Lock Sashiko - BLQK Manual

18
Zoom out
Zoom in
Previous page
1/43
Next page
G
E
T
T
I
N
G
R
E
A
D
Y
17
Winding the Bobbin
a
b
c
A
B
1. Slide the spool of thread onto the spool pin. (Fig. A)
2. Slide the correct size spool cap onto the spool pin.
(Fig. B)
Spool cap should be close in size to the thread spool,
however should not be smaller. If the spool cap is small-
er than the thread spool, thread may get caught in the
slit on the end of spool and cause damage.
3. Place the thread into the thread guide for bobbin wind-
ing (a), and insert the thread into the pre-tension disk (b)
until the thread snaps into place. Then lay the thread
into the bobbin winder adjustable thread guide (c).
(Fig. C)
4. Insert the end of the thread through one of the holes in
the bobbin going from the inside of bobbin to the outside
as illustrated. (Fig. D)
5. Place the empty bobbin on the bobbin winder shaft.
While holding the thread tail securely in one hand, push
the bobbin winder shaft to the right toward the bobbin-
winder lever. (Fig. E)
Press the foot control to wind bobbin. (Fig. F)
After the bobbin has wound a few turns stop the
machine, cut the thread near the hole of the bobbin and
then continue with bobbin winding.
NOTE: When winding the bobbin the desired speed can
be set with the foot control. Press on the foot control
slowly until you have reached your desired speed.
Maintain the speed for at least 3 to 4 seconds then pres-
sure can be released from foot control. The speed will
maintain constant until the foot control is tapped once to
stop the machine or until the bobbin is fully wound.
6. The bobbin winder will stop automatically once the
bobbin is fully wound and the top LED light will flash the
color blue. (Fig. G)
7. Slide the bobbin winder shaft with the bobbin to the left
and grasp the full bobbin and pull upward to remove.
8. If the thread is winding uneven while winding the bobbin
(Fig. H); adjust the bobbin winder balance adjusting
screw with screwdriver by turning it clockwise toward the
(+) symbol to raise the thread guide or counterclockwise
toward the (–) symbol to lower. (Fig. I)
C
D
E
F
G
H
I
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Sashiko - BLQK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Sashiko - BLQK in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info