661207
108
Zoom out
Zoom in
Previous page
1/128
Next page
Troubleshooting
A-4
If the machine stops operating correctly, check the
following possible problems before requesting service.
You can solve most problems by yourself. Visit us at
“ www.babylock.com
”.
If the problem persists, contact your authorized Baby Lock
retailer.
Frequent troubleshooting topics
Detailed causes and remedies for common troubleshooting
topics are described below. Be sure to refer to this before
contacting us.
Upper thread tightened up
Symptom
The upper thread appears as a single continuous line.
The lower thread is visible from the upper side of the
fabric. (Refer to the illustration below.)
The upper thread has tightened up, and comes out
when pulled.
The upper thread has tightened up, and wrinkles
appear in the fabric.
The upper thread tension is tight, and the results do
not change even after the thread tension is adjusted.
1 Wrong side of fabric
2 Bobbin thread visible from right side of fabric
3 Upper thread
4 Right side of fabric
5 Bobbin thread
Cause
Incorrect bobbin threading
If the bobbin thread is incorrectly threaded, instead of the
appropriate tension being applied to the bobbin thread, it
is pulled through the fabric when the upper thread is
pulled up. For this reason, the thread is visible from the
right side of the fabric.
Remedy/check details
Correctly install the bobbin thread.
a
Turn off the machine, and then raise the presser foot
lever.
b
Remove the bobbin from the bobbin case.
c
Place the bobbin in the bobbin case so that the thread
unwinds in the correct direction.
Hold the bobbin with your right hand with the thread
unwinding to the left, and hold the end of the thread
with your left hand.
Then, with your right hand, place the bobbin in the
bobbin case.
If the bobbin is inserted with the thread unwinding in
the wrong direction, sewing will be done with an
incorrect thread tension.
d
While holding the bobbin in place with your finger,
pass the thread through the slit in the needle plate
cover.
Hold down the bobbin with your right hand, and
then pull the end of the thread around the tab with
your left hand.
1 Tab
2 Hold down the bobbin with your right hand.
Troubleshooting
Upper thread tightened up page A-4
Tangled thread on wrong side of fabric page A-5
Incorrect thread tension page A-6
Fabric is caught in the machine and cannot
be removed
page A-7
If the thread becomes tangled under the
bobbin winder seat
page A-10
Error message “E06” appears in the LCD page A-11
108


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Baby Lock Presto BLMPR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Baby Lock Presto BLMPR in the language / languages: English as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Baby Lock Presto BLMPR

Baby Lock Presto BLMPR Quick start guide - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info