66170
27
Zoom out
Zoom in
Previous page
1/52
Next page
27
27


The mounting location of the power amplifier will have a large
effect both on its ability to dissipate the heat generated during
normal operation through the heat sink and on the possible triggering
of its internal overheat protection shut-off circuit. 



Therefore select a suitable location that is convenient for mounting and
accessible for wiring and offers sufficient ventilation for cooling. As your
amplifier features no controls for normal operation, it may be mounted
away from the dashboard, i.e. under a car seat or in the trunk. However,
make sure the unit is not exposed to excessive dust, direct sunlight,
humidity, water, oil or other fluids that may enter the amplifier.

The amplifier should be mounted to a solid surface that will ensure
a vibration-free mount. Once the location is selected, use the unit
as a template for the marking of the mounting holes which should also
be pilot-drilled before mounting of the amp is carried out.

Secure the amplifier using the four screws. Avoid to let the am-
plifier get into contact with metal parts of the vehicle. This helps
to prevent unwanted ground loops.


Please note: wrong power or signal connections may damage the am-
plifier and other components connected to it. Therefore, please read
this manual carefully before the connection of any power, signal and
speaker leads is done.
The wire routing is critical for noise-free performance. For best results,
please follow the general wiring guidelines listed below (for details see
section B, E, F and G of this manual).

For audio signal connections you should always use double or
triple shielded quality RCA cables.

Signal, speaker and power cables should always be kept as short
as possible:
Speaker and power cables may be cut to fit the actual length
required.
Shielded RCA/signal cables should never be cut and respliced,
as they will loose their protective shielding effect at those points
where they have been cut. If the signal cable is too long, make an
S-type loop (never a coil loop) in the centre of the cable to take-up
the excess length.

Never route any low level/signal cable near or parallel to speaker
outputs/speaker cables, amplifier power cables or high energy
ignition wires.

Use power cable with the recommended cross section (see
section E). Small cross sections are reducing the output power,
are causing distortions and may be triggering the overheat protection
of the amplifier.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Axton A485 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Axton A485 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info