66170
26
Zoom out
Zoom in
Previous page
1/52
Next page
26
26
bm Separate input gain/sensitivity
controls for channels 1+2 respectively allowing the matching of the
amplifier input section to the head-unit (pre-out) output voltage.
bn


Depending
on the selected switch setting the amplifier for channels 1+2 operates in
Fullrange, Highpass or Lowpass mode.
bo 
Crossover filter frequency
control for channels 3+4 allowing the setting of the respective lowpass
cutoff frequency between 40 and 240Hz.
bp Crossover filter frequency
control for channels 3+4 allowing the setting of the respective highpass
cut-in frequency between 40 and 240 Hz.
bq Separate input gain/sensitivity
controls for channels 3+4 respectively allowing the matching of the
amplifier input section to the head-unit (pre-out) output voltage.
br


Depending on the selected switch setting the amplifier for channels 3+4
operates in Fullrange, Highpass or Lowpass mode.
bs Low-level RCA signal input for
connection to head-unit (Rear) pre-out for a speaker pair or a subwoofer
that will be either driven in Fullrange or Lowpass amplifier mode.
bt Low-level RCA signal input for
connection to head-unit (Front) pre-out for a speaker pair that will be
either driven in Lowpass, Fullrange or Highpass amplifier mode.
1 Power connection terminal to chassis ground or
negative terminal of car battery (-12 V).
2 Remote switching contact for the automatic
(remote) turn-on / turn-off of the power amplifier from the head-unit's
remote (or antenna control) lead.
3 + 12 V Power connection terminal to positive terminal of car
battery.
4  Fuse for protection of the amplifier-internal electronics
against over-load or faulty operation / wrong manipulation.
5 A A Speaker output terminals
for channels 1+2; i.e. one stereo speaker pair in fullrange, highpass or
lowpass mode (e.g. subwoofer). 

6 A A Speaker output terminals
for channels 3+4; i.e. one stereo speaker pair in fullrange, highpass or
lowpass mode (eg. subwoofer). 

7 Amplifier status-LED – located on the side of the
amplifier – signalling normal operation – when lit green.
8 Lit red when amplifier is in protect mode due to
shorted speakers, overtemperature etc.
9 
Crossover filter frequency
control for channels 1+2 allowing the setting of the respective lowpass
cutoff frequency between 40 and 240Hz.
bl Crossover filter frequency con-
trol for channels 1+2 allowing the setting of the respective highpass cut-in
frequency between 40 and 240 Hz.


26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Axton A485 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Axton A485 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info