621854
4
Zoom out
Zoom in
Previous page
1/14
Next page
CAMCOLBUL22N
06.12.2010 ©Velleman nv
4
o The connection cables run at the inside of the mounting bracket, and leave at the backside [3]
(default). They can be re-guided to leave via the top [4] or bottom [5] of the mounting
bracket.
o Note that the camera must be resting on top of the mounting bracket.
When the cables go through the wall:
o [B] Use the wall mounting bracket to determine and indicate the position of the mounting
holes.
o When the connection cables need to go through the wall, a hole of at least Ø10mm (max.
Ø35mm) must be foreseen at the mounting location, close to the centre of the drawn template.
Mount the mounting bracket on the wall using 4 screws (included).
Guide the connection cable into the mounting bracket and guide the connector out through the
desired hole ([3], [4] or [5]). Never exert excessive stress on the connection cable to avoid
damage. Rotate the camera to the desired angle and place the camera on the mounting bracket
making sure there is no stress on the connection cable.
Tighten hex screw [7] to secure the horizontal position and hex screw [6] for the vertical
position.
[C] Connect the connection cable with the BNC/power adaptor cable [Y]. This is only possible in
one way; do not force. Use some waterproof tape (not inc.) to make the connection completely
watertight.
Connect the video connector [1] to a monitor (not incl.).
Connect the power connector [2] to a 12VDC power supply (not incl.).
The sunshield can be mounted or dismounted by releasing the two screws on top of the camera
and sliding it towards the rear.
7. Technical specifications
pick-up element 1/3" HR colour CCD
number of pixels 752(H) x 582(V) - PAL -
resolution 520 TV lines
min. Illumination 0.1 Lux (F1.4); 0 Lux (IR on)
S/N ratio > 48dB (AGC off)
electronic shutter 1/50 to 1/100000 sec
gamma correction 0.45
white balance automatic
AGC yes
standard board lens f6.0mm/F1.4
lens angle 62°
video output 1.0Vpp composite, 75 ohms
power supply 12VDC ± 10% (regulated, use PS1205R, not incl.)
consumption 70mA (IR off), 590mA (IR on)
IP-rating IP67
IR LEDs 56
max. IR projection distance 40m
dimensions Ø115.6 x 216.4mm
weight 1350g
operating temperature 0°C to +40°C
Use this device with original accessories only. Velleman nv cannot be held responsible
in the event of damage or injury resulted from (incorrect) use of this device. For more
info concerning this product, please visit our website www.velleman.eu. The
information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
This manual is copyrighted. The copyright to this manual is owned by Velleman nv. All worldwide rights
reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or
otherwise without the prior written consent of the copyright holder.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AVTech - Velleman CAMCOLBUL22N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AVTech - Velleman CAMCOLBUL22N in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info