722161
6
Zoom out
Zoom in
Previous page
1/38
Next page
Wireless Bridge: Connect the FRITZ!Repeater 3000 to
the Wireless Router using the Wizard
If your wireless router does not support setup at the touch of a button (WPS), use the
wizard to connect the FRITZ!Repeater 3000 with the wireless router.
1
Connecting to the Computer
1. Connect the FRITZ!Repeater 3000 with an outlet close to your wireless router. The
FRITZ!Repeater 3000 starts operation.
2. Wait until the “Connect” LED starts slowly ashing green.
3. Select the wireless radio network of your FRITZ!Repeater 3000 on the computer, and
start the connection process.
4. Enter the network key of the FRITZ!Repeater 3000. The precon gured unique network
key is printed on the back of this guide and on the bottom of the device housing.
The computer establishes a connection to the FRITZ!Repeater 3000.
2
Run the Wizard
1. Open the web browser on your computer and enter http://fritz.repeater in the
address bar.
2. The con guration wizard appears and guides you through setup of the wireless
connection between the FRITZ!Repeater 3000 and your wireless router.
3. Connect the FRITZ!Repeater 3000 to an outlet located about halfway between the
wireless router and the wireless devices to be added to the wireless network.
The FRITZ!Repeater and your wireless router connect once more. The “Connect” LED
and the LED for connection quality light up as soon as the wireless connection is
established.
LED for connection quality lights up green
the FRITZ!Repeater 3000 has a good wireless connection and is ready for operation.
LED for connection quality lights up orange
the FRITZ!Repeater 3000 has a weak wireless connection. Position the FRITZ!Repeater
closer to the wireless router.
LED for connection quality continuously ashes orange
the wireless connection cannot be established. Position the FRITZ!Repeater closer to
the wireless router.
LAN Bridge: Connect the FRITZ!Repeater 3000 to the
Internet Router Using a LAN Cable
If you would like to connect the FRITZ!Repeater 3000 with your FRITZ!Box (router) by cable,
con gure “LAN bridge” access mode in the user interface of the FRITZ!Repeater 3000.
LAN Bridge access mode can be con gured via a LAN connection or over the
wireless network. These instructions assume that the FRITZ!Repeater is connected
with the computer via LAN cable. For instructions on how to con gure this access
mode wirelessly, see the PDF manual on our website
en.avm.de/service.
Con gure LAN bridge
1. Connect the FRITZ!Repeater with your computer via LAN cable.
2. Connect the FRITZ!Repeater3000 to an outlet.
3. Wait about 1 minute until the FRITZ!Repeater 3000 starts operation.
4. Open a web browser on the computer and enter http://fritz.repeater. The user
interface of the FRITZ!Repeater 3000 appears.
5. Assign a password for the user interface and click “OK”.
6. Enter the password again and click “Log In” and “Next”.
7. Enable the “LAN Bridge” access mode and click “Next”.
8. Follow the wizard’s further instructions.
1110
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for AVM Fritz Repeater 3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of AVM Fritz Repeater 3000 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of AVM Fritz Repeater 3000

AVM Fritz Repeater 3000 Usermanual and installation guide - German - 97 pages

AVM Fritz Repeater 3000 Usermanual and installation guide - Dutch - 97 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info