Manual Autoterm Flow (page 14 of 36) (English)

814909

Zoom out

Zoom in

1/36

Fig. 10 - Installation of the air intake pipe

1 – Air intake pipe;

4 – Gasket;

2 – Flange of the air intake pipe;

5 – Fastener assembly;

3 – Hull of the vessel;

6 – Clamp.

3.4 Installation of the exhaust pipe.

When installing the exhaust pipe, take into

consideration the high temperature (up to 500°С) of the

exhaust pipe when the heater is in operation. Cut the

exhaust pipe (flexible crinkled metal hose, maximum

length – 2 meters) to the necessary length. It is advised to

use a two-layer exhaust pipe when installing the heater.

Attach the exhaust pipe (Fig.11) using clamps and install

it so that it is slightly inclined to the bottom, in the

direction of the exhaust. Install heat insulation on the

exhaust pipe to protect individual sections of the vessel

(wiring or other heat-sensitive objects).

Fig. 11 - Attachment of the metal pipe

to the heater

Install the exhaust pipe to avoid the possibility of repeated intake of exhaust

gases by the air intake pipe, and make sure that no exhaust gases enter the interior

or are drawn in by the fan through the cab heater radiator.

At the end of the exhaust pipe, a shield is installed, which is necessary for stable

operation at low heating modes (Fig.13).

In the absence of the shield, air will be blown back

into the exhaust pipe. This leads to increased heater

sooting and impairs heat capacity. Exhaust gases must be

expelled outside of the vehicle.

An airtight exhaust silencer is provided with the

heater. This means it can be mounted in small vessels

and confined spaces. When mounting the exhaust

silencer on the outside of the vehicle, a Ø5mm hole

needs to be drilled at the bottom of the silencer (see Fig.

14a).

Cut 15 mm

Shield

Heat insulation

Fig. 13 – Exhaust pipe shield

Clamp

Heater

Metal exhaust

pipe

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Autoterm Flow in the language / languages: English as an attachment in your email.

The manual is 5.3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Autoterm Flow

Autoterm Flow User Manual - German - 37 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Autoterm Flow Manual

Product: