701388

Autotek TA2150 Manual

10
Zoom out
Zoom in
Previous page
1/32
Next page
10
AUDIO SIGNAL CABLES
WheninstallingtheaudiocablesbetweentheRCAoutputsoftheheadunitandtheRCAinputsoftheamplier,
the audio and power supply cables should, if possible, not be routed along the same side of the vehicle. We
recommend a separated installation, e.g. routing the power cable through the cable channel on the left side
and the audio cables through the cable channel of the vehicle on the right side or vice versa. This prevents
interferences due to crosstalk into the audio signal.
INPUT SENSITIVITY
OPERATING ELEMENTS
TurntheGAIN(Fig.1,3)controlleroftheampliertotheMINposition.Thenturnthevolumecontrollerofthe
head unit to 80 - 90% of its full setting. Now turn GAIN clockwise until you hear some distortion. Then turn back
the GAIN slightly until you hear a cleaner sound.
HIGH LEVEL INPUTS
TheHIGHIN(Fig.1,2)issuitabletoconnecttheamplierinputswithspeakerwires,ifyourheadunitisnot
equippedwithpre-amplierRCAoutputs.Extendthereforeveryregardingspeakercablefromyourheadunit
withappropriatespeakercablesfromyourcaraudioretailertothemountinglocationoftheamplier.Thencon-
nect the each matching loudspeaker cable with the cables of the included HIGH IN jack like described below.
ATTENTION: Never use the High Level Input and the RCA inputs at the same time. This may damage the
amplierseriously.TheloudspeakercablesoftheHIGHINmusthavenocontacttotheground(GND)byany
means.
grey = speaker - right - positive
brown = speaker - right - negative
white = speaker - left - negative
green = speaker - left - positive
VARIABLE HIGH PASS FILTER
Iftheamplieristobeusedformid-range/tweeterloudspeakers,settheswitchesX-OVER(Fig.1,6)toHPF.
Then set the desired cross-over frequency on the HPF controller (Fig.1,7). Thus to that only the frequencies
abovethechosencross-overfrequencywillbeamplied.Thiseffectivelyminimizesdistortionsandoverloads
at lower frequencies. A good point to start is at 125 Hz.
If you use loudspeakers (>20 cm) set X-OVER (Fig.1,6). to ”FULL”. In this case, the HPF controller are without
function (Fig.1,7).
VARIABLE LOW PASS FILTER
If theamplier is usedto drive asubwoofer,set theswitch (Fig. 1,6) to „LPF“. Set the desired cross-over
frequency by using the controller (Fig. 1,5). Thus to that only the frequencies below the chosen cross-over
frequencywillbeampliedandthesubwooferplaysmorepreciselyandefcient.
SWITCHABLE BASS EQ
By using the BASS EQ switch (Fig.1,4) you are able to increase the bass level by 6 or 12 dB at 60 Hz.
Attention: Use the BASS EQ wisely!
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Autotek TA2150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Autotek TA2150 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info