701388

Autotek TA2150 Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
9
IMPORTANT NOTES PRIOR TO INSTALLATION
- This device is only suited for a 12 volt system with negative ground.
- Theradiatedheatwhileoperationrequiressufcientaircirculationattheplaceofinstallation.Itis
veryimportantthattheheatsinknsdonothavecontactwithanymetalpartsoranysurfaceswhich
couldimpairaircirculation.Theampliermaynotbeinstalledinsmallclosedlocationorspaces
without air circulation (e.g. spare wheel recess or below the vehicle carpeting). We recommend the
installationinthevehicle’strunk.Ensuresufcientprotectionagainstvibrations,dustanddirt.
- Ensurethattheinputandoutputcablesaresufcientlyseparatedfromthepowersupplycables.
Otherwise interferences may occur.
- Ensure the accessibility of the fuse and the operating elements after installation.
- Thereliabilityandperformanceoftheamplierdependsonthequalityofinstallation.Preferably
consult an expert to install the system, particularly if you want to install several loudspeakers.
POWER SUPPLY AND TURN-ON-CONNECTION
INTERCONNECTION
ATTENTION: Before you start with the installation, disconnect the ground connection from the ve-
hicle’s battery in order to prevent short circuits.
Thepowerwiringwhichisusuallyinstalledinon-boardcarnetworksisnotsufcientforapoweramplier‘s
demands.MakesurethatthepowerwirestoGNDandtothe+12Vterminalhasbeensufcientlyspecied.A
cable cross section of at least 10 mm
2
mustbeusedtoconnectthebatterytotheamplier‘sterminals.
FirstconnecttheGNDterminaloftheampliertoanappropriategroundconnectionatthechassis.Toensurea
good connection, residue dirt and dust from the connection point. A loose connection may cause malfunctions
or interferences noise and distortion.
Thenconnectthe+12Vterminaloftheamplierwiththebatterybyusinganappropriatecableincludingan
in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30 cm
away. Only insert the fuse when the installation, including the connection of the loudspeakers, has been ac-
complished.
Thenconnect theremoteturn-on-wire from theheadunit withtheamplier‘s REMterminal.A cablewitha
cross-section of 0.5 mm
2
is adequate.
LOUDSPEAKER CONNECTIONS
- In2-channeloperation(i.e.oneloudspeakeroneachamplierchannel),theimpedancemust
not be lower than 2 ohms for each speaker
- Inbridgingmode(twoamplieroutputscombined)theimpedancemustnotbelowerthan4ohms
for the bridged output.
- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.
Iftheamplierisoperatedwithatoolowimpedanceorincorrectlyused,theentiresoundsystemmaybedam-
aged. This means a warranty void in such cases.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Autotek TA2150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Autotek TA2150 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info