558054
8
Zoom out
Zoom in
Previous page
1/48
Next page
INFINITY4
AUTOBAR
2.3 Connecting the Electrical Supply
Safety First! Your machine must be earthed. On no account should it be earthed
only
to the water supply pipe.
Your machine must be connected to a 230 Volt 50Hz 13 amp fused switched socket outlet,
installed to the latest edition of the IEE regulations, using a 3 pin BS approved 13 amp fused plug.
Important: If the mains lead becomes damaged in any way it must be replaced by a special lead
available from the manufacturer.
Important: If any internal fuses become damaged or fail in any way they must be replaced by a
special fuse available from the manufacturer quoting the information written on the label adjacent
to the relevant fuse-holder
2.4 Commissioning Procedure
A trained installation engineer must carry out the following procedure before your machine can be
used for the first time. Ensure that the electrical and water services to the machine are connected
correctly. Check for leaks in the water supply.
1. Open the front door of your machine.
2. Ensure that the waste bucket is fitted correctly. Clip the level detector and overflow
pipes correctly onto the rim of the bucket.
3. Cup Turret. Remove the cup stack assembly from its packaging and carefully place it
onto the cup drop unit, ensuring that the flat on the turret drive shaft locates with the
corresponding flat in the cup turret mounting block. Remove the lid and fill the tubes
with the correct size cups for the cup catcher type fitted to your machine.Allow the
cups to drop into the tubes directly from the packaging. DO NOT touch the cups with
your hands.
Important: Do not fill the tube directly above the cup dispense position. Allow the cup
turret motor to rotate a full tube to the cup dispense position when the machine is
powered up. Rotating the cup turret by hand will damage the mechanism.
Note: If you are loading paper cups, first inspect each pack for damage to the cup rims.
Damaged cups must not be used.
4. The cup turret mechanism will index the first available full cup stack to the dispense
position and drop the cup stack into the cup drop mechanism. Fill the remaining empty
cup stack with cups and replace the lid.
5. All Models: The water inlet valve will open and the heater tank will start to fill. As the
water heats, ensure that no water overflows from the heater tank overflow pipe into the
waste bucket. When the machine has powered up, the LCD will display the message
“Sorry Out of Service Water Tank Heating”. Check the system for leaks.
Note! The machine has a safety cut-out which will only allow the heater tank to fill for a
maximum of two minutes. If after software power-up the heater tank has not filled within
this time, the mains power supply should be switched off and then on again to reset the
heater tank time-out.
Important: Should the machine fail to fill correctly or leak, turn off the stopcock and the
power to the machine before investigating the fault.
6. ChecktheLCD displayonthe front ofthemachine toensurethat thewaterhas heatedto the
correct temperatureand thatthemachine isin standbymode.Amachinesetto freevend
mode willalternatethemessages:Please MakeaSelection/NoMoney Required”.
Section 2 - Installation (Engineerʼs Procedure)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Autobar Infinity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Autobar Infinity in the language / languages: English as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Autobar Infinity

Autobar Infinity Installation Guide - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info