694349

Austroflamm Polly light Manual

81
Zoom out
Zoom in
Previous page
1/88
Next page
english 78
5.3. Safety temperature delimiter
Your pellet stove has a safety temperature delimiter fitted on the back. This switches off the stove
automatically in the case of overheating. In this case, you must determine the cause of overheating
(back-burning, etc.) and eliminate it. After doing this, press the reset button on the safety temperature
delimiter back in to make the stove ready for operation again.
6. Cleaning/servicing
Because cleaning intervals depend greatly on the installation location and operating hours, the times
stated in the following table can only be considered to be reference values. Basically, all of the following
components must be cleaned depending on their degree of contamination. A service engineer must carry
out annual servicing.
Cleaning the viewing window Approximately 15
operating hours or if
necessary
Visual inspection of the burner bowl and grate, remove clinging deposits Ben, Polly light, Percy
light: each time they
have been switched off,
other models
approximately 2 - 3
days
Emptying of the ash box and cleaning of the combustion chamber Every week or if
necessary
Cleaning of the flue gas ducts, flue gas collectors and exhaust duct blowers Once a year
Cleaning of the screw conveyor chute and pellet tank Once a year or if pellet
feeding is obviously
reduced
Replace the battery 2 years
Inspection of all the seals (door, ash box, tank lid, blower housing, etc.);
replace if necessary
Once a year
Cleaning of the chimney as per the chimney sweep specialist Min. once a year
7. Replacing the Battery of the Control Unit
During a power failure, or if the mains power supply is cut off, the control unit switches to internal battery
power supply. The battery supplies the internal clock and internal memory of the microprocessor.
If the battery is empty, the control unit functions normally as long as the mains power supply is
connected. In the event of a power failure, the internal clock stops and the operating phase is not saved
in the memory. After the power supply has been restored, the clock is reset and the control unit remains
in theOFFor “Fire up” phase.
This is how to replace the battery (approximately every two years):
Safety temperature delimiter
79 english
16. Disconnect the mains power supply.
17. The battery is located on the circuit board. To do this, you must first remove the side panel.
18. Use insulated pliers or a similar tool to remove the old battery from its holder. Make sure that you
do not bend the contacts of the battery holder.
19. Insert the new battery making sure that the correct polarity is maintained (see Abbildung 3:
Austauschen der Batterie.
20. Reconnect the mains power supply.
Figure 12: Replacing the battery
8. Wifi box & PelletControl
As-standard, models Polly 2.0 and Percy are fitted with a Wifi box; you can retrofit the Wifi box as
an accessory for the Ben, Percy light and Polly light models. The Wifi box allows you to integrate
your pellet stove into your existing wifi network and to monitor and control it using your smartphone
(under iOS and Android).
Download the necessary app PelletControl and start it:
Apple iOS Google Play / Android
The system displays the following prompt: “Have you connected the heating device to your wifi
network yet?”
"No"
“Your heating device will be connected to a wifi network”: Enter your wifi password here and press
the wifi button on the wifi box on the back of the stove. The LED there starts to flash faster. While
the LED is flashing fast, press “Start wifi setting” on your smartphone.
When the wifi LED is lit up permanently and the status LED is flashing, press “Stop wifi setting” on
your smartphone.
Navigate back to where you are prompted to enter your MAC address and pin code (see the sticker
on the wifi box). Enter the data.
When all the LEDs are lit up permanently, press “Connect”.
-
+
Button battery
CR2032
englisch
… 81 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austroflamm Polly light at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austroflamm Polly light in the language / languages: English, German, French as an attachment in your email.

The manual is 5,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Austroflamm Polly light

Austroflamm Polly light User Manual - Dutch - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info