815458

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II Manual

98
Zoom out
Zoom in
Previous page
1/122
Next page
11 | Installation EN Operating manual Fireplace inserts slied flat + II
98
Calibration: The calibration (see above) of the controls is carried out when the controls are connected
to the mains or the WLAN is changed, but only if the flue gas temperature is below 80 ° C. In the pro-
cess the control software detects where the positions 0% and 100% shutter opening are on its fireplace
insert. After the controls have detected the two maximum positions, they run to the 0% shutter open-
ing (if the correct program has been chosen) and switches into the Standby phase.
This process requires approximately 10 minutes. Should the flue gas temperature be above 80°C, no
calibration run is carried out. The controls use the data from the last calibration run that was carried
out.
The programming of the controls includes various “Eco” and “Normal” combustion curves. Each of
these two modes is available with the “sliding opening” and “sliding closing” function.
Program overview
Selection wheel Mode Function
Position 0 - Shutter opening, always 60%
Position 1 Normal sliding opening
Position 2 Eco sliding opening
Position 3 Normal sliding closing
Position 4 Eco sliding closing
Selecting the program
Fig.76: Unplugging the power supply
1) Remove power supply from the socket.
2) Remove the three screws and open the control unit
housing.
1
Fig.77: Selecting the program
On the circuit board is a selector switch (1) that by default is
set to position “0”.
3) Select program by setting the arrow of the selector
switch to position 1, 2, 3 or 4 (see “Program Overview”
table.
4) Before closing the controls again, carry out a fresh cal-
ibration by plugging the power supply back in.
ðIf you have selected the correct “sliding closing” or
“sliding opening” function, after the calibration the
controls must complete close the shutter.
ðShould you notice that you have chosen the wrong
program, you can change this in the service menu
of the app.
APP
The InsertControl function can be monitored using the app on iOS and Android Smartphones. To do
so, first load the “InsertControl” app from the iTunes Store or Google Play on to your Smartphone.
When it is connected to the circuit, InsertControl creates a WLAN with the name “ABR_xxxxxxx”
(xxxxxxx = serial number of the controls). You must connect your Smartphone to this network (pass-
word: 12345678). After the app is started, the connection is automatically established.
If desired you can then connect the app to another WLAN (in the app’s settings menu). Please note
that a new calibration run for the controls will then be started.
… 98 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II in the language / languages: English as an attachment in your email.

The manual is 14.06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II

Austroflamm Fireplace inserts slied flat II - Kamineinsatz Schieb flach II User Manual - German - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info