800537

Austria Email KRU 102 Manual

21
Zoom out
Zoom in
Previous page
1/72
Next page
21
Id.Nr. 235161-13
8. CORROSION PROTECTION
The enamelled boiler is protected by a magnesium rod-type anode as standard. The magnesium rod-type anode is sacricial
and must therefore be inspected every 2 years (see DIN 4753) and replaced as necessary (2/3 of the material). The degra-
dation products of the magnesium anode can precipitate as dissolved matter in the bottom area of the tank and also be
rinsed out from the tank during the water withdrawal. For the anodes to function properly, the water requires a minimum
conductivity of 150 μS/cm.
When retrotting an external current anode, ensure that all magnesium rod-type anodes (e.g. in built-in heater) are removed
to prevent interference and malfunctions of the external current anode.
See Point 12, Par. C for details on servicing the anode.
The impressed current anode has a virtually unlimited service life. Its function must be regularly monitored via the control
lights (green, yellow, red).
Warning: If the red LED is lit, no corrosion protection is active! Corrosion protection is only guaranteed if the green LED lights
up continuously.
Should the red or yellow LED light up or ash, please inform Customer Services immediately.
The connection cable of the impressed current anode may in no case be extended or cut, because otherwise a possible
polarity reversal or malfunction of the anode may occur. In addition, it is to be ensured that a permanent power supply is
ensured.
Important: All metallic components (e.g. heaters, pipe register) must be introduced in a manner that is electrically
isolated from the tank.
A missing or incomplete corrosion protection (missing anode service for magnesium anode) leads to the exclusion of
the warranty.
9. TEMPERATURE INDICATOR, THERMOSTAT FOR FEED PUMP
When installing external thermostats, ensure that the boiler temperature cannot rise above 95°C during normal operation.
10. INITIAL STARTUP
The area in which the appliance is operated must be kept below freezing.
Initial startup and heating must be monitored by a technician.
Before rst starting up and connecting to the electrical mains, the tank must be lled with water. When rst lled the outlet
valve on the tting must be opened. The water heater is completely lled when water runs out of the outlet valve with no
air bubbles. All connections, including those made on the user side (ange, anode sleeve,…) must be checked for proper
sealing when starting up. Then check the pipelines for any leakage and remedy this as needed. As described under 2. above,
the safety group as well as the valves between cold water inlet and water heater must be checked for proper function. After
inspecting the electrical fuses (circuit breakers), turn the thermostat knob (for electric upright and horizontal water heaters)
to the desired temperature setting and check for the correct temperature shut-o.
After the tank is fully heated, the set temperature, the actual temperature of the water removed and any built in temperature
indicator must closely agree (after deducting the switching hysteresis and line losses).
As the water in the tank is heated, its volume changes.
During the heat-up cycle the resulting expansion water in the internal boiler must drip from the safety valve. This dripping is
normal and may not be defeated by increased tightening of the valves.
Check for automatic shut-o of the system and any attached electric heater insert or the boiler.
Caution: The hot water outlet pipe as well as parts of the safety tting can become hot to the touch.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austria Email KRU 102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austria Email KRU 102 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info