800537

Austria Email KRU 102 Manual

19
Zoom out
Zoom in
Previous page
1/72
Next page
19
Id.Nr. 235161-13
4. HEATING INSERTS
Important: All metallic components such as SH, RWT, and/or EBH are to be inserted electrically insulated from the tank. To
protect the built-in parts from corrosion, a transition resistance of about 600 Ω is to be provided (if not yet installed in the
built-in parts at the factory).
Screw-in heater
Water heaters whose model name contains an „..M..“, are tted with a 1 1/2“ sleeve which can be used to install an electric
screw-in heater for supplementary or auxiliary heating. Screw-in heaters are designed technically as supplementary heating,
and should not be used for continuous heating (failure due to natural calcication is not a sucient reason for claim). It is also
important to ensure that when an SH heater is used in enamelled hot water tanks, an insulated design is available opposite
the tank (see RWT).
Ribbed tube heat exchanger
All metallic insert (ush mounted) components having a larger metallic surface area (e.g., condenser insert heat pumps,
ribbed tube heat exchangers, electric heaters) must be electrically isolated from the water heater. In order to protect these
insert (ush mounted) components against current-induced corrosion, we recommend installing a dened contact resis-
tance of approx. 600 Ω (unless already installed in the components ex works). The water heaters may not be transported with
the ribbed tube heat exchanger installed. Installation must be performed on-site. Attention must be paid to full overlapping
of screw threads on all coupling sleeves. When installing a ribbed tube heat exchanger, make sure that the storage tank is still
protected against corrosion.
Therefore, an appropriate external current anode or magnesium reactive anode must be mounted when the magnesium
reactive anode is removed from the storage tank with the ange plate during assembly of a ribbed tube heat exchanger.
Electric built-in heater
Appliances with electrically powered built-in heaters are equipped with a safety temperature limiter which turns o further
heating of the appliance at a temperature of max. 110 °C (EN 60335-2-21; ÖVE-EW41, Part 2 (500)/1971). Therefore, select the
connection components (pipe ttings, circulation, safety valve combination, etc.) such that they will resist temperatures of
110 °C in the event of any possible malfunction of the thermostat and thus preventing consequential damage.
Assembly and installation may be performed only by authorized specialists.
A built-in heater, installed via the ange, is provided for continuous operation.
The built-in or screw-in heaters must be installed or designed with insulation (at least 600 Ω), as otherwise the tank interior
may corrode.
If the corrosion protection is built-in to the ange plate as standard, alternative corrosion protection must be provided if the
ange plate is removed.
Due to the hysteresis of the thermostat (±7 K) and potential dissipation losses (cooling of the pipelines) the temperatures can
deviate by ±10 K.
If the water heater is heated via its heat exchanger, ensure that the hot water temperature cannot exceed 85 °C under any
circumstances, as it could trigger the safety temperature limiter of the electric heater, and shut the heater down.
5. FLANGE INSERTION OPENING
Depending on the system design, electric built-in heaters or heat exchangers
can be installed on the boiler ange Ø240 mm (clear diameter Ø173 mm,
hole circle Ø210 mm, 12 x M12) and Ø180 (clear diameter Ø117 mm, hole
circle Ø150 mm, 8 x M12).
Built-in electric heating elements are to be installed so that the thermostat
probe is at the top.
The screws must be tightened in a cross pattern with a tightening torque of
23 Nm - 25 Nm.
Flange ring
Gasket
Spacer
Range plate
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austria Email KRU 102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austria Email KRU 102 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info