800525
14
Zoom out
Zoom in
Previous page
1/28
Next page
DEX 18 / 21 / 24 / 27 KW
14
Elektroanschluss von oben
Vergewissern Sie sich vor dem
Anschließen des Gerätes an
das elek trische Netz, dass die
Stromversorgung ausgeschaltet ist!
1. Öffnen Sie die im oberen Gerätebereich
vorhandene Sollbruchstelle (S) an
der Prägung durch kräftigen Druck
mit einem stumpfen Werkzeug (z.B.
Schraubendreher).
2. Schneiden Sie die Durchfüh rungs tülle
(22) entsprechend dem Zuleitungs-
querschnitt auf. Dabei soll die Öffnung
in der Tülle etwas kleiner als der
Quer schnitt des Kabels sein, um einen
optimalen Schutz gegen Wasser zu
erzielen. Passen Sie die Tülle in den
Durchbruch ein. Die Schutz tülle muss
verwendet werden!
3. Manteln Sie das Elektrokabel unge-
fähr 6 cm über dem Wand austritt ab.
Nehmen Sie das vorbereitete Gerät so
in die Hand, dass Sie mit der anderen
Hand das Kabel in die Gummi tülle füh-
ren können.
4. Setzen Sie das Gerät so auf den Wand-
halter (10), dass die Gewindestange
des Wandhalters in das vorgesehene
Loch des Gerätes passt.
5. Lösen Sie die Befestigungs schraube der
Anschlussklemme. Versetzen Sie die
Anschluss klemme auf den oberen Fuß.
Befestigen Sie die Anschluss klemme
dort wieder.
6. Isolieren Sie die Kabel ab und schlie-
ßen diese an die Anschlussklemmen
gemäß des auf Seite 12 abgebildeten
Schaltplanes an. Das Gerät ist an den
Schutzleiter anzuschließen.
7. Setzen Sie das Gehäuse auf das Gerät
und drehen Sie die Befestigungs-
schraube ein. Danach können Sie die
Blende aufrasten.
Electrical connection from
above
Check that the power supply is
switched off prior to electrical con-
nection!
1. Open the prepared breaking point (S)
in the upper part of the appliance by
pressing with a blunt implement
(e.g. srewdriver).
2. Slit the grommet (22) to match the
cable size. The opening in the grommet
should be slightly smaller than the
cross-section of the cable in order to
ensure optimum protection against
water. Fit the grommet into the ope-
ning. The protection grommet must be
used!
3. Strip the cable roughly 6 cm above the
point where it emerges from the wall.
Hold the prepared appliance so that
you can route the cable into the grom-
met with the other hand.
4. Place the appliance on the heater
bracket (10) so that the threaded rod
of the wall bracket fits in the provided
hole of the appliance.
5. Unscrew the fastening screw of the
connecting terminal. Displace the
connecting terminal to the upper foot.
Affix the connecting terminal again.
6. Insulate the cables and plug them in
the connecting terminals according to
the wiring diagram on page 12. The
appliance must be earthed.
7. Place the hood on the appliance and
screw in the fastening screw. After
that you can reinsert the faceplate.
S
9. Elektroanschluss 9. Electrical connection
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austria Email DEX18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austria Email DEX18 in the language / languages: English, German as an attachment in your email.

The manual is 2.99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info