800525
12
Zoom out
Zoom in
Previous page
1/28
Next page
DEX 18 / 21 / 24 / 27 KW
12
Nur durch den Fachmann!
Zu beachten sind:
• VDE 0100
• EN806-2
• Bestimmungen der örtlichen
Energie- und Wasserversorgungs-
unternehmen
• Angaben Typenschild
• Technische Daten (Seite 7)
• Gerät an Schutzleiter anschließen!
Bauliche Voraussetzungen
• Das Gerät muss dauerhaft an fest
verlegte Leitungen angeschlossen
werden. Das Gerät muss an den
Schutzleiter angeschlossen werden.
Kabelquerschnitt maximal 10mm2.
• Die Elektroleitungen müssen sich in
einem einwandfreien Zustand befinden
und dürfen nach der Montage nicht
mehr berührbar sein.
• Installationsseitig ist eine allpolige
Trennvorrichtung mit einer Kontakt-
öffnungsweite von mindestens
3 mm pro Pol vorzusehen (z.B. über
Sicherungen).
• Zur Absicherung des Gerätes ist ein
Sicherungselement für Leitungsschutz
mit einem dem Gerätenennstrom an ge-
passten Auslösestrom zu montieren.
Lastabwurfrelais
Beim Anschluss weiterer Drehstromgeräte
kann ein Lastabwurfrelais für elektroni-
sche Durchlauferhitzer an den Außenleiter
L2 angeschlossen werden.
LCD Beschreibung
0Normaler Betrieb,
Werkeinstellung
1Betrieb mit normalem
Lastabwurfrelais
2Betrieb mit empfindlichem
Lastabwurfrelais
Drücken Sie zum Ändern der Betriebsart
gleichzeitig alle vier Tasten ( , ,
und ) und warten, bis der gewünschte
Wert (0, 1 oder 2) im Display erscheint,
dann Tasten loslassen. Zunächst ist die
Schaltplan / Wiring diagram
Only by a specialist!
Please observe:
• The installation must comply with
current IEC or national local regu-
lations and any particular regula-
tions, specified by the local elec-
tricity supply company
• Observe the rating plate and tech-
nical specifications (page 7)
• The unit must be earthed!
Structural prerequisites
• The appliance must be installed via a
permanent connection. Heater must
be earthed! A maximum cable size of
10 mm2 must be observed.
• The electric wiring should not be
injured. After mounting, the wiring
must not be direct accessible.
• An all-pole disconnecting device (e.g.
via fuses) with a contact opening
width of at least 3 mm per pole should
be provided at the installation end.
• To protect the appliance, a fuse ele-
ment must be fitted with a tripping
current commensurate with the nomi-
nal current of the appliance.
Load shedding relay
If further three-phase appliances are con-
nected, a load shedding relay can be con-
nected to phase conductor
L2
.
LCD Description
0Normal operation,
manufacturer‘s setting
1Operation with normal
load shedding relay
2Operation with sensitive
load shedding relay
A special operating mode must be selec-
ted on the appli ance for this purpose.
To change the operating mode, press
the four keys ( , , and ) simul-
taneously and wait until the desired mode
(0, 1 or 2) is shown on the display, then
9. Elektroanschluss 9. Electrical connection
1. Elektronik
2. Heizelement
3. Sicherheitsdruckbegrenzer und
Sicherheitstemperatur begrenzer
4. Klemmleiste
1. Electronic circuitry
2. Heating element
3. Safety pressure switch and Safety ther-
mal cut-out
4. Terminal strip
21
4
3
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Austria Email DEX18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Austria Email DEX18 in the language / languages: English, German as an attachment in your email.

The manual is 2.99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info