563992

Auriol Z31092 - IAN 94604 Manual

10
Zoom out
Zoom in
Previous page
1/69
Next page
10 GB/IE
from your device and from the local weather
forecasting service, please take the advice of the
latter as authoritative.
Press the HISTORY / WEATHER button
27
for about 3 seconds. The weather symbol
1
flashes.
Set the current weather by pressing
the “+“ / °C / °F button
28
or the
“–“ / MAX / MIN
button
29
.
You can choose between the following
weather symbols:
= sunny
= light clouds
= cloudy
= cloudburst /
storm
= rainy
Press the HISTORY / WEATHER button
27
to
confirm your settings.
Note: Ensure that you have set the current
weather correctly, otherwise the weather
forecast will not be correctly displayed.
The weather station starts with the weather
forecast approximately 6 hours after you
enter the current weather.
The weather station can display the barometric
pressure trend
25
. You may see the following
displays:
= the barometric pressure will rise.
= the barometric pressure will remain
constant.
= the barometric pressure will fall.
Reading the barometric
pressure
Press the Relative / absolute barometric pres-
sure button
30
to switch between the relative
and absolute barometric pressure display.
Note: The display shows “Abs” if you have
selected absolute pressure. The display shows
“Rel” if you have selected relative pressure.
Note: The absolute barometric pressure is
measured by the weather station.
Set the relative barometric pressure to the
barometric pressure relative to that at sea
level. Ask your local weather forecast service
for the barometric pressure at sea level.
Press and hold down the Relative / absolute
barometric pressure button
30
for about
3 seconds.
Set the current barometric pressure by press-
ing
the “+“ / °C / °F button
28
or the
“–“ / MAX / MIN
button
29
.
Press the Relative / absolute barometric
pressure button
30
to confirm your settings.
Reading the barometric
pressure for the last 12 hours
Press the HISTORY / WEATHER button
27
to read the barometric pressure values for
the last 12 hours.
 0HR = present barometric pressure
– 1HR = barometric pressure an hour earlier
– 2HR = barometric pressure two hours
earlier, etc.
Press and hold down the “+“ / °C / °F button
28
for about 3 seconds to switch between
displaying the barometric pressure units in
inHg or mb / hPa.
Setting the channel
To do this open the battery compartment on
the back of the outdoor sensor and take it off.
Set the channel by means of the Channel
selection switch
39
.
Press the channel button
26
for approx. 3
seconds until a signal is sounded. The wea-
ther station has now received one signal.
Press the TX button
42
to transmit the measured
temperature to the weather station manually.
Then close the battery compartment
40
.
Displaying the outdoor
temperature
Press the Channel button
26
to display the
outdoor temperature of each outdoor sensor.
– Press the Channel button
26
1 x to display
channel 1.
– Press the Channel button
26
2 x to display
channel 2.
– Press the Channel button
26
3 x to display
channel 3.
– Press the Channel button
26
4 x to display
all the channels one after the other in a loop.
Only the outdoor sensors which can be
addressed are displayed.
Press and hold down the Channel button
26
to remove unused channels. If a further out-
door sensor and channel are added later,
the weather station will receive the signal
automatically. Alternatively, you can also
transmit the initial signal from the outdoor
sensor manually by pressing the TX button
42
.
94604_aur_Funk-Wetterstation_content_GB_FI_DK.indd 10 28.08.13 13:16
… 10 …


Need help? Post your question in this forum.

Forumrules
1

Forum

auriol-z31092---ian-94604

Reset search

  • Hi,
    My Auriol 433 MHz remote sensor has stopped working.
    My main unit is working perfectly.
    I confirmed that it was the sensor by borrowing another from a friend and his works OK with my main unit. (Obviously I have checked that my remote batteries are OK.)
    Can I buy a new or second hand remote sensor anywhere.
    George Walker, Bromley, UK Submitted on 24-7-2018 at 11:59

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Auriol Z31092 - IAN 94604 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Auriol Z31092 - IAN 94604 in the language / languages: English, German, Dutch, Danish, French, Swedish, Finnish as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info