583950

Audiovox AS9233ST Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
128-8604
4 of 8
2. Within 10 seconds begin to enter tenths digit of override code. (In this ex-
ample the code is 11, so press and release the push-button switch found on the glass
mounted receiver assembly one time).
3. Within 10 seconds of entering the last tenths digit, turn ignition “off then on”.
4. Within 10 seconds of turning the ignition switch on, begin to enter units digit
of override code. (In this example the code is 11, so press and release
the push-button switch found on the glass mounted receiver assembly one time).
5. Within 5 seconds after the last units digit is entered, turn the ignition switch
off, then on, and start your vehicle.
If the manual override code is entered properly, the unit stops sounding, the LED turns off,
indicating a successful override. The system is now disarmed and you can start and
operate your vehicle. The unit will allow three attempts to disarm via the manual override
sequence. If the code is not successfully entered within the three attempts, disarming with
the manual override switch will be locked for 10 minutes.
In many cases, to increase the security of your system, you may elect to change the manual
override code to a number that is more familiar to you, or simply to have a different code
than was pre-assigned from the factory. To Change the pre-assigned override code follow
the steps outlined below.
It is advised you read both sections under the headings “Programming Your Custom Over-
ride Code” and, “Custom Code Programming Example”, To completely understand the proce-
dure before beginning:
Programming Your Custom Override Code:
Unlike override switches easily found, and defeated, this system allows the con-
sumer to program a personal override code, offering a higher level of security. The system
comes from the factory with a pre-programmed override code of 11. To change this default
override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the push-button switch found on the receiver
assembly 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing
and releasing the push-button switch from 1 up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then
on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing
and releasing the push-button switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code, by flashing
the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the
new code three times with a one second pause between each code, then the system will
begin arming. If the LED flash pattern reports the previously stored code, the new code
was not entered correctly. Please repeat steps 1 through 7 above considering the follow-
ing.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize
a 0 (Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert back
to the last successfully stored code.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you
would do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence.
Page 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiovox AS9233ST at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiovox AS9233ST in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info