583772
7
Zoom out
Zoom in
Previous page
1/8
Next page
7
FEATURE ACTION TO PERFORM RESPONSE FROM SYSTEM LED FLASH PATTERN
To Turn the Ignition Switch ON LED Turns OFF
Enter Toggle the Valet/Program/Manual Override Switch
The ON then OFF 3 Times 1 Siren/Horn Chirp & 1 LED Flash
Programming Within 3 seconds
,
Mode turn the Ignition Switch OFF, then ON 1 Short Chirp, and 1 Long Chirp
First Press Transmitter Button 1 to Change Feature 1 Chirp = Passive Arming ON 1 Flash, Pause, Repeat
2 Chirps = Active Arming ON
Second Press Transmitter Button 1 to Change Feature 1 Chirp = Ign Locking ON 2 Flashes, Pause, Repeat
2 Chirps = Ign Locking OFF
Third Press Transmitter Button 1 to Change Feature 1 Chirp = Ign Unlocking ON 3 Flashes, Pause, Repeat
2 Chirps = Ign Unlocking OFF
Fourth Press Transmitter Button 1 to Change Feature 1 Chirp = Chirps ON 4 Flashes, Pause, Repeat
2 Chirps = Chirps OFF
Fifth Press Transmitter Button 1 to Change Feature 1 Chirp = Passive Doorlock ON 5 Flashes, Pause, Repeat
2 Chirps = Passive Doorlock OFF
Sixth Press Transmitter Button 1 to Change Feature 1 Chirp = Steady Output (siren) 6 Flashes, Pause, Repeat
2 Chirps = Pulsed Output (horn)
Seventh Press Transmitter Button 1 to Change Feature 1 Chirp = 800ms Lock Pulse 7 Flashes, Pause, Repeat
2 Chirps = 3.5sec Lock Pulse
3 Chirps = 800ms Lock Pulse
800ms Double Unlock
You have now engaged the Programming Mode, and are set to adjust the First feature
This mode will time out automatically in 15 seconds, or can be cancelled by turning the Ignition Switch OFF
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Turn the Ignition Switch OFF to exit the Programming Mode
NOTE:
If you accidentally toggled past the feature you intended to adjust, you must exit and re-enter the mode.
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
OR
Toggle the Valet/Program/Manual Override Switch once to Advance to the next feature
COMPLETING THE INSTALLATION:
After you have confirmed the operation of the APS-45, and tested any and all optional features of the system:
1. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain that the
chosen mounting location will not inhibit any of the controls of the vehicle.
2. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact with
under the dash board or in the engine compartment areas.
CAUTION:Particularly avoid the area around the steering shaft and column, as wires can wrap around these
mechanisms and impair the safe operation of the vehicle.
3. Check the vehicle's wipers, lights, horn, etc... to insure proper operation.
4. Replace all panels that were removed during installation, and retest the system.
5. Explain the operation of the system and its various features to the end user if available, and place the Owner's
Manual on the dashboard for them to find and review.
NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between steps, or
the programming mode will be terminated.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Audiovox APS-45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Audiovox APS-45 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info