810499

ATTACK DPX Manual

42
Zoom out
Zoom in
Previous page
1/92
Next page
42
• degree of flammability C2 normal combustibility (softwood (pine, spruce), chipboard,
solodur)
• degree of flammability C3 easily ignited (wood fibre boards, polyurethane, PVC, foam rubber,
polystyrene)
The sealing board or protection covering (on the protected item) must exceed the boiler edge
for at least 300 mm. Also other items from flammable materials must be protected in this way, if
they are placed near the boiler and it is not possible to keep the safe distance.
If the boiler stands on a flammable surface, it must be protected by an inflammable, heat
insulating mat, which exceeds the edge on the side of the feeding door and the ash tray door for
at least 100 mm. All materials of the A flammability degree can be used as an inflammable, heat
insulating mat.
The boiler must be placed in a such way ensuring sufficient space of at least 1 m from the front
and 0,5 m from the left (right) and rear side. It is necessary to leave the space of at least 1 m
above the boiler.
This space is necessary for basic operation, maintenance and eventual service of the boiler. It is
not allowed to place the boiler in dwelling premises (including corridors). There must be an
opening for the air inlet for burning of at least 200 cm
2
depending on the boiler output.
CAUTION! The items from flammable materials must not be laid on the boiler and in the
distance shorter than the permitted (safe) one. The boiler must be turned off, if there is
a danger of fire or explosion due to the work (e.g. work with painting materials, glues, etc.).
Air inlet
For correct operation of the boiler it is necessary to ensure sufficient air supply for burning.
There must be an opening for the air inlet for burning of at least 200 cm
2
depending on the
boiler output.
Boiler connection to the heating system
Only a trained technician can install and service the ATTACK DPX boiler. Before installing the
boiler, it is necessary to flush (to clean) the whole heating system. The system can be filled only
the water treated to the values under the STN 07 7401: 1992. Callosity of the water must not
excess 1mmol/l and concentration of the Ca²Ѐ must be lower than 0,3 mmol/l.
If these conditions are not kept, the warranty is not valid!
Chimney
Connection of the appliance to the chimney hole must be always done with permission of the
appropriate chimney sweep association. The chimney must generate sufficient draught and take
the flue gas out into the atmosphere under the all operating conditions.
Correct dimensions of the chimney hole are important the correct boiler function, because the
burning, output and boiler life-time are influenced by the draught. The chimney draught directly
depends on its diameter, height and roughness of the internal wall. It is not allowed to connect
any other appliance to the chimney, where the boiler is connected. Diameter of the chimney
must not be smaller than the connection part on the boiler. The chimney draught must achieve
the prescribed values, but it cannot be too high, not to decrease the boiler output and interrupt
the burning (flame). If there is too strong draught, install the throttle flap into the chimney hole
between the boiler and the chimney.
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATTACK DPX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK DPX in the language / languages: English as an attachment in your email.

The manual is 11.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATTACK DPX

ATTACK DPX Additional guide - English - 21 pages

ATTACK DPX Additional guide - German - 21 pages

ATTACK DPX User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info