Manual ATTACK DPX Combi Pellet (page 43 of 100) (English)

810510

Zoom out

Zoom in

1/100

The burners ATTACK PELLET BURNER Automatic works on basis of the fuel feeding by the

principle of falling, when the pellets fall by from the pellet feeder through the inlet hose and the

inlet tube on the grate, where they are burned.

The burners have an electrical ignition that automatically lights the pellets fallen on the grate.

Starting the burner is controlled by adjusting the burner and boiler temperature or room ther-

mostat, if it is connected. Start and stop temperature can be set in menu with buttons on the

controll panel of the burner. Information about actual operation data is given on display.

The burners have an own self–cleaning mechanism of the grate. When the thermostat reaches

the adjusted off–temperature, the burn–out cycle begins and afterwards, the grate moves out to

be cleaned by scraping. This enables longer time of use, without need to remove the burner

from the boiler. Convectional parts of the boiler have to be cleaned in regular intervals to keep

the high efficiency of heating.

The boiler can be used only moulded wood pellets without additional materials and with

following parameters:

Approved fuel specification:

Measured weight: 600 – 750 kg/m

Heat value: 4,7 – 5,0 kWh/kg

Size/diameter: 6 mm

Size/length: Attention! Max. 35 mm

Moisture max.: 12 %

Ash content: 0,5 – 1 %

Dust content: max. 3 %

Ash smoulder temperature: min. 1 100 °C

Standards : DIN 51 731 – HP 5, DIN Plus, or EN 14961–2 – A1

Regulation of the pellet dosing

Before starting–up the burner, it is necessary to set the pellet supply through the parameter of

the „Stoker Adj.“ in the Advanced menu. Thermostat cannot start the heating while the settings

are being made. Firstly, set the parameter of the „heat value“ to the value given by your pellet

supplier. If the supplier gives 4,8 kWh/kg, set the parameter to 48, etc.

Now, put the plastic bag around the opening of the pellet feeder. Then, confirm by the „S“ but-

ton and keep the instructions. Weigh the pellets fallen into the plastic bag, put their weight in

gramms via the „+/−“ buttons and press the „S“ to save the values. This setting has to be done

within 15 minutes, otherwise the burner switches to the stand–by mode. Weigh the pellets very

exactly!

After setting of the above mentioned parameters, the control system automatically sets all the

parameters relative to the pellet feeding.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ATTACK DPX Combi Pellet in the language / languages: English as an attachment in your email.

The manual is 8.73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ATTACK DPX Combi Pellet Manual

Product: