769373
31
Zoom out
Zoom in
Previous page
1/67
Next page
Atomos Ninja V – User Manual Edition 1: Aug 2021 29
Timecode
Using Timecode
The timecode display changes position depending on
the screen mode you are using. In monitoring mode it
appears in the center top, below the info bar. In home
screen mode the timecode display sits on the bottom
near the REC PLAY MON EDIT icons.
Touching the Timecode display on the home screen,
just below the information bar will take you to the
Timecode setup screen.
The Timecode modes supported are:
HDMI (Embedded)
Record Run
Time of Day
Auto Restart
Cycle through these modes by touching the
Timecode Source Selector.
7. Using the Ninja V
Source
Tap to cycle through the timecode modes:
HDMI/SDI embedded Timecode
With this setting, the HDMI/SDI input will use the Timecode
embedded in the input signal. The controls to adjust the Timecode
value are disabled in this menu as you will need to adjust these on
the camera. Note that not all HDMI/SDI sources embed Timecode.
Trigger from HDMI Timecode
If HDMI timecode is selected and the camera is in REC RUN mode,
the user has the choice to start and stop recording remotely from the
source camera timecode.
To enable rolling Timecode Start/Stop functions, simply set the
HDMI Timecode switch to on. When enabled, pressing the camera
Record Stop/Start button will make the Ninja V start and stop record
simultaneously as the timecode starts and stops.
When using the camera in Free Run timecode, the rolling timecode
trigger might not work as expected.
Note that whilst camera triggers are also looped out on HDMI not all
wireless systems carry the trigger on to other devices so it’s worth
testing your system before a shoot if you pan to use it in this way to
record proxies.
Time of Day
With this setting, each new clip that is created will contain embedded
Timecode starting with the time of day when the recording is started.
Please check that Ninja V clock has been set correctly.
This can be set in the DATE menu
If recording is stopped and then restarted while in this mode, there
will be a time gap between the last clip and the next one, equal to the
length of time the Ninja V has been out of record.
In Time of Day mode, the controls on the Timecode Setup Screen for
adjusting the start-point of the Ninja’s Timecode are not available, as
the Timecode is set by the Ninja’s internal clock.
Record Run
WiththissettingyousetthestartingTimecodefortherstclip.The
following clips will start at the frame immediately after the out point of the
preceding clip. This will continue for all clips that follow. This is also
known as continuous Timecode.
Auto Restart
With this setting, the Timecode will be reset to the Timecode you have
denedwheneveryoupressrecord.Allyourclipswillstartwiththissame
Timecode.
To adjust the Timecode use the “+” and “-” above and below the
hour:minute:seconds sections
Use Drop Frame
Allows you to use drop frame timecode type.
HDMI Out Timecode
Allows you to output the timecode chosen here on the Output of the Ninja.
Timecode
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atomos NinjaV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atomos NinjaV in the language / languages: English as an attachment in your email.

The manual is 29.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atomos NinjaV

Atomos NinjaV User Manual - German - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info