553036
64
Zoom out
Zoom in
Previous page
1/69
Next page
64
5. Pitch Sensitivity – This is the time that it takes for the waveform display to become
adjusted after you alter the pitch of the timecode signal. Too small of a value will attempt
to redraw the waveform when you scratch the timecode, which is not recommended.
Setting too high of a value will take longer to redraw the waveform, which may be visually
confusing. Please experiment with a few different values to find the one best suited for
your style.
6. Anti Skip – If enabled, anti skip will prevent playback from skipping if the needle happens
to jump to another groove. Please note that anti-skip is only available under Smart or
Relative modes.
7. Smart Cue – If enabled, moving the needle far to a different location on the timecode
record (over more than one groove segment away) will cause the software to
automatically jump to the next set cue point (forward or backward), instead of jumping to
the absolute location where you drop the needle.
8. Browser Track – If enabled, Browser Track allows you to use the timecode signal to
browse through your music in the software. With Browser Track feature enabled, the last
three groove segments become dedicated to browsing, so when you drop the needle onto
one of these segments, you can scroll through your music titles by moving the record
forward and backward.
9. Signal – Select the appropriate time code signal to be used based on your Timecode of
choice.
10. Arrows – Pressing one of the arrows will copy the timecode preferences to the other
deck.
11. Software RIAA Preamp – If enabled, allows you to plug a phono-level turntable directly
into a line-level input on the sound card.
The following settings (12-17) will be set by the Auto-Config feature so you do not have
to worry about understanding them. The software will automatically configure them for
you:
12. Gain – The gain compensation for the timecode signal.
13. Silence – Compensates for background/ambient noise by lowering/raising the noise floor
threshold.
14. Stereo – Used to set the balance of input between left and right signals. Ideal position
would be where in View 2 the signals are equal in strength and form.
15. Invert Stereo – Virtually switches the left and right inputs and effectively reverses
playback.
16. Invert Phase – Software adjustment if your needle is wired incorrectly.
17. TC Up – Level of “1” value in the binary signal of the timecode
18. TC Down – Level of “0” value in the binary signal of the timecode.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atomix Virtual DJ 5.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atomix Virtual DJ 5.1 in the language / languages: English as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info