580238

ATN Night Arrow 2 - 2 Manual

4
Zoom out
Zoom in
Previous page
1/8
Next page
3
To change the position of the riflescope on the weaver rail additionally follow the steps men-
tioned below:
1. Unscrew the two screws, which attach the rail to the
mounting bracket.
2. Take the rail out of the groove.
3. About-face the rail in case of necessity.
4. Place the rail into another groove.
5. Fix the rail with the two screws.
NOTE: If the rail does not come out easily, tighten one of the removed screws into the threaded
aperture in the middle of the fixing projection of the rail. Rotate this screw, which will in turn push
the rail out from the groove.
CONTROL
The Night Arrow 2 has a simple and easy to operate one-knob control and adjustment.
To turn riflescope on rotate the operation knob from position marked “0”.
To turn riflescope off rotate the operation knob to position marked “0”.
After turning scope on, you may adjust the reticle’s brightness by rotating the operation knob
from position marked “1” to position “9”. Position “1” corresponds to the minimal brightness,
the position “9” corresponds to the maximal brightness of reticle’s glow.
Adjustment could be easily seen if you look through the scope while adjustment.
FOCUSING
To focus your riflescope you will need to adjust the diopter. Simply turn the diopter clockwise
until it stops. Then, while looking through the diopter at a subject, slowly turn the diopter back
counter clockwise until the grain in the image is sharp.
NOTE: We suggest that you focus the diopter during daylight with the cap on.
OPERATION EXTENDIBILITY
There is Picatinny rail on the body of the scope for additional lighting, laser and other mission
critical tools.
IR ILLUMINATION
Infra-red (IR) Illuminators are common for night vision technology. The IR light greatly
enhances the performance of your Night Arrow 2 scope, while remaining almost totally invis-
ible to the naked eye. In dark environment, power up the ATN Night Arrow 2. Now, find a scene
and examine it without the IR on then with IR powered up. Note the difference in illumination. It
is important to remember that the IR illuminator is simply an infra red light source, and like any
light source it may loose its effectiveness over a great distance.
To fix the IR illuminator to the riflescope use the picatinny raile of the scope.
The IR illuminator control buttons are located on its side. To switch the Digital IR illuminator
on/off press “+” and “-” buttons simultaneously. When the IR illuminator is switched on you can
see the green LED lit. By pushing the buttons “+” and “-” you may adjust the IR brightness.
IR Brightness
Adjustment
Battery
Housing
Fixation
Screw
IR Elevation
IR Windage
IR Focusing
Nut
Groove
Rail with a
fixing projection
Screws
Mounting
system
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATN Night Arrow 2 - 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATN Night Arrow 2 - 2 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info