613599
7
Zoom out
Zoom in
Previous page
1/45
Next page
7
COMFORT Mode : User selects a hot water temperature between 50°C and 65°C (default value of 65°C). Warning: this operating
mode might increase the electrical consumption of the product.
MAX Mode : User selects a hot water temperature between 65°C and 75°C (default value of 70°C). Warning: this operating mode
increases the electrical consumption and scaling. Using hot water with high temperature may cause burns. It is strongly recommended to
take all the necessary precaution to use this operating mode.
5/ Temperature display (Ref. F):
In FROST FREE Mode , it indicates the temperature setpoint of 7°C automatically fixed by the product.
In SMART Mode , the displayed value is the temperature setpoint automatically analysed and fixed by the product. When a large
quantity of hot water is used, the displayed temperature is the one measured close to the bottom side of the product (30cm for a 50L
product, 40cm for 80L and 100L). That means the remaining quantity of hot water is limited (10L of hot water remaining for a 50L product,
30L remaining for a 80L product and 50L remaining for a 100L product).
In MINI , COMFORT and MAX modes, it shows the temperature of water inside the tank. When pushing the setting keys
(Ref. B), the screen displays during a few seconds the setpoint temperature chosen by the user before displaying again the water
temperature inside the product.
6/ Heating indicator (Ref. E): Shows when the water is under heating. NOTA: if the indicator is on continuously, that means the product is under
heating. It doesn’t reveal a bad running of the product.
7/ Control panel locking (Ref. G): To lock or unlock the control panel, press simultaneously the UP and DOWN buttons
TROUBLESHOOTING
When a malfunction occurs, the user interface of the appliance will display an error code.
Code
Fault
Concerned element
Actions
E1
Probe fault
Thermostat
Unplug and plug the power supply
If the problem is not resolved, contact your installer or dealer
E2
No heating
Thermostat
Hot water circuit
Heating element
1/ Check that there are no problems on the hot water circuit (open tap, burst pipe...)
If a leak is found, solve the problem, disconnect and reconnect the power supply to the unit and
check that the default does not reappear during the first heating.
2/ Check that the circuit breaker is not tripped thermal
Disconnect power supply
Open the cover of the device
Check the thermostat
If the circuit breaker has tripped
reset it by pressing the button SAFETY on the thermostat
close the cover of the device
reconnect the power supply and check that the default does not reappear in the first
heating.
If the default reappears, contact your installer or dealer (service code: ERR9).
3/ None of the previous two cases
Contact your installer or dealer (service code: ERR0)
E3
Over heating
Thermostat
Check that the circuit breaker is not tripped thermal
Disconnect power supply
open the cover of the device
check the thermostat
If the circuit breaker has tripped
reset it by pressing the button SAFETY on the thermostat
close the cover of the device
reconnect the power supply and check that the default does not reappear in the first
heating.
If the default reappears, contact your installer or dealer (service code: ERR9).
If the circuit breaker is not tripped, contact your installer or dealer (service code: ERR9)
E4
Dry heating
Cold water circuit
1/ Check that the cold water supply is operational
2/ Open hot water taps and see the water flow. If the flow is not immediate, wait lines are
purged of air
If the flow of the hot water circuit is sufficient
Disconnect and reconnect the power supply to the unit and check that the default does not
reappear.
If the default reappears, contact your installer or dealer (service code: Err7).
If the flow of hot water is absent, contact a qualified professional to intervene in the cold
water supply of the unit.
EN
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atlantic Ingenio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atlantic Ingenio in the language / languages: English, French, Polish as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info