475731

Atika VT32 Manual

21
Zoom out
Zoom in
Previous page
1/162
Next page
20
• Fight the moss with a commercially available agent before
aerating.
• Proceed as described under “Scarifying”.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning work:
− switch off device
− wait until the drum is stationary
− pull out main plug
Maintenance and cleaning activities beyond those described in this
chapter may only be performed by customer service.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
To make sure that the device is in a safe condition regularly check
the device for apparent defects such as
− loose fastening elements (nuts, bolts, screws),
− catching bag for wear or damaged parts,
− worn or damaged components.
Maintenance
Blade replacement L
Worn blades reduce the performance of the device and put
excessive strain on the motor. Therefore check the condition of the
blades before each use. If necessary, have the blades sharpened
by an expert or replaced by new ones.
Wear protective gloves when working with
the blades. Risk of injury!
The blades can be turned. To turn the blades, proceed as
follows:
1. Loosen the head screws (31) at the seat of the bearing (30).
2. Remove the scarifier drum (29).
3. Loosen the hexagonal nut (a) and remove the cover cap (b), the
flange (c), the blades (44) and the spacers (d) from the axle (e).
4. Turn the blades or insert new ones and install the drum again in
the opposite sequence.
Replace worn or damaged blades only as a set to avoid
imbalances!
5. Retighten the hexagonal nut and place the drum in the device.
Spring replacement G
To replace the springs, proceed as follows:
1. Loosen the head screws (31) at the seat of the bearing (30).
2. Remove the aerator drum (41).
3. Loosen the hexagonal nut (a) and remove the washer (b) and
cover cap (c).
4. Insert new springs (45) and install the drum again in the
opposite sequence.
Pay attention to the correct position of the springs.
5. Retighten the hexagonal nut and place the drum in the device.
Cleaning
L
Clean the device carefully after each use to ensure
faultless function to be maintained.
Clean the device immediately after finishing the work.
Empty and clean the grass catching bag if necessary.
Clean the bottom of the device and the scarifier or aerator
drum.
Clean the housing, especially the vent slots, from grass and dirt
stuck to it.
Remove the dirt with a cloth or brush.
Do not clean the machine with running water or high-pressure
cleaners.
Do not use solvents for the synthetic parts (petrol, alcohol, etc.)
as these can damage the synthetic parts.
Wear protective gloves when working with
the blades. Risk of injury!
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
Pull the mains plug prior to transport.
The drum can be damaged during transport, e.g. on hard
ground, even when the motor is switched off. Therefore set
the work depth of the drum to position 1 during transport.
S
S
t
t
o
o
r
r
a
a
g
g
e
e
Pull out main plug.
Store unused equipment in a dry, locked place out of the reach
of children.
In case of extended storage (e.g. during winter) ensure that the
device is protected against frost and corrosion.
Before extended storage, please observe the following to
increase the service life of the device and to ensure smooth
operation:
− thoroughly clean the device
− Treat metal parts after each use against corrosion using an
environmentally friendly biologically degradable spray oil.
L
Never use any grease!
To facilitate space-saving storage of the device, you can
fold down the handle hoop. Loosen the wing nuts (6) for this
purpose until the handle hoop (2) can be folded down onto
the housing. C
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika VT32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika VT32 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info