475731

Atika VT32 Manual

20
Zoom out
Zoom in
Previous page
1/162
Next page
19
1. Pull out the stop lever.
2. Push it to the desired position.
3. Allow the stop lever to catch again.
4. Set the same work depth at both wheels.
Work depth Position
(from rear)
Scarifier Lawn aerator
1 4,0 mm 10 mm
2 0,5 mm 6,5 mm
3 -3,0 mm 3,0 mm
4 -6,5 mm -0,5 mm
5 -10,0 mm -4,0 mm
L Set the work depth according to the grass and ground
conditions at both running wheels.
Recommended work depths:
Position
Regularly scarified soft ground; without stones 5
Seldom scarified mossy ground; with stones 3 / 4
Uncultivated very mossy; with stones 1 / 2
Set a lower work depth when the motor is straining (motor
speed drops and motor noise changes).
Example: Work depth set to 5 Î change to 4
W
W
o
o
r
r
k
k
i
i
n
n
g
g
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
Before commencing work, ensure the following:
You may not start to operate the machine until you have read
these operating instructions, observed all the instructions given
and installed the machine as described!
Provide for a safe and cleaned workplace. Remove from the
working area objects which might be thrown off.
Before starting your work make sure that:
− the tools and bolts are not worn or damaged. To avoid any
unbalance worn or damaged tools and bolts must only be
replaced as a whole set.
− drum and blades are in proper condition (see “blade
replacement”)
− all screw connections are tight
− no other persons or animals stay within the working area,
− you can always step back without any barriers,
− you have always a secure standing position.
Always keep your hands and feet at a safe distance to
the rotating tool.
Vibration
If persons who have blood circulation problems are too often
exposed to vibrations damages to the nervous system or to blood
vessels may occur.
You can reduce vibrations
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your fingers swell, you don’t feel well or your fingers
become numb.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
s
s
c
c
a
a
r
r
i
i
f
f
i
i
e
e
r
r
Scarifying
Using the scarifier drum, the device can be used as scarifier
to remove mats and mosses in the lawn and to cut through wild
growth with low roots.
To enable the growth of a healthy lawn in spring, the absorption of
water, air and nutrients in the root area needs to be increased. We
recommend scarifying the lawn in spring and autumn.
To achieve good results and to extent the life of the scarifier drum,
the lawn should be mowed before scarifying (shorter than 4 cm).
L Do not scarify when the lawn has been freshly sown or when
it is wet or too dry.
• Place the scarifier at the edge of the lawn near the receptacle.
• Move the cable after each turn to the opposite already scarified
side. K
• Select the work depths according to the condition of the lawn
(see “Setting the work depth”).
• Make sure not to place excessive strain on the scarifier.
L In case of excessive strain, the motor speed drops and
the motor noise changes.
Î Stop and release the switch lever
Î Wait until the scarifier drum stands still
Î Set a lower work depth
• Move the scarifier at an appropriate uniform speed in straight
lines across the lawn.
L The lawn surface will be damaged if you let the scarifier
run too long at one spot.
• In case of uncultivated very mossy lawn, move once more
across to the rows setting the work depth then to a higher
position (e.g. from 4 to 3)
• When working on slopes, always position yourself perpendi-
cular to the incline and ensure safe footing. Do not scarify on
steep slopes.
• Empty the grass catching bag when it is full to prevent the
blades from being blocked and subsequently the motor from
being overloaded.
• Mow the lawn once more after scarifying.
• Reseed blank spots that may have developed after scarifying.
• Fertilize the lawn only after fresh grass seeds have put down
roots.
In any case, adhere to all safety notes (see "Safe
working").
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
l
l
a
a
w
w
n
n
a
a
e
e
r
r
a
a
t
t
o
o
r
r
Aerating
With the aerator drum (optional accessory, if applicable) the
device can be used as lawn aerator to remove grass and moss as
well as cutting through wild growth with low roots.
To enable the growth of a healthy lawn in spring, the absorption of
water, air and nutrients in the root area needs to be increased. We
recommend aerating the lawn, depending on the condition, every
6 – 8 weeks.
To achieve good results and to extent the life of the aerator drum,
the lawn should be mowed before aerating (approx. 2 cm).
• Install the aerator drum (see “Assembly”)
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika VT32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika VT32 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info