520145

Atika KSL2401-40 Manual

25
Zoom out
Zoom in
Previous page
1/148
Next page
24
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning work
− switch off device
− wait for stop of chain saw
− pull out main plug
Further maintenance and cleaning works than described in this
chapter shall only be carried out by the manufacturer or
companies named by the manufacturer.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance
In order to avoid possible injuries wear gloves.
To guarantee a long and reliable usage of the chain saws carry
out the following maintenance works regularly.
Check the chain saw for obvious defects such as
− loose, hung out or damaged saw chain
− loose fastenings
− worn or damaged components
Check the chain saw after each application for
− wear, especially chain, guide bar and chain wheel.
− correctly assembled and faultless covers and protective
devices.
Necessary repair works or maintenance works have to be
carried out before the usage of the chain saw.
Sharpening of saw chain
You can only work safely and well with a sharp
and clean saw chain. Damaged or incorrectly
sharpened saw chains increase the risk of
kickbacks.
The saw chain has to be sharpened if
½ only wood dust is thrown out instead of shavings
½ you have to press the chain saw through the wood during
cutting
L Inexperienced users: Have the saw chain sharpened by a
specialist/service workshop.
You can also sharpen your saw chain yourself by using our
electric sharpener KSG 220 (article-no.: 302360).
Saw chain type Oregon 91 VG 057X
Depth gauge distance T .025“ (,64 mm)
Sharpening angle α 30°
Breast angle β 60°
Planing tooth length a min. 3 mm
Exchanging saw chain and guide bar
Saw chain and guide bar are exposed to great wearing
demands. Immediately exchange saw chain and guide bar
when the faultless function is not guaranteed.
B
Put the chain saw on an even face.
B
Remove the cover (10) by loosening the fastening screw
(11).
B
Turn the chain clamper (22) anti-clockwise in order to
release the saw chain a bit.
B Take off the guide bar with saw chain.
B Clean the guide slot thoroughly when only the saw chain is
exchanged.
B
When assembling, pay attention that the chain links are
lying correctly within the guide slot and on the chain wheel
(13).
B Turn the chain clamp (22) clockwise until the saw chain is
clamped.
B Now, refasten the cover (10).
B Clamp the saw chain as described in paragraph „Clamping
of saw chain“.
Chain wheel
The demand of the chain wheel (13) is particularly great. Check
regularly the teeth of the chain wheel for wear or damages.
L
A worn or damaged chain wheel reduces the
durability of the saw chain and should therefore
immediately be exchanged by the customer service.
Checking of the oil automatic
Check the function of the automatic chain lubrication by
switching on the chain saw and holding it with the pike in
direction of a carton or paper on the ground.
Do not get in contact with the ground with the chain. Keep a
safe distance of 20 cm.
If an increasing oil track is caused when checking it the oil
automatic works faultless.
If there is no oil track despite full oil tank
B
clean the oil flow canal (14) and the upper chain
clamping boring (15).
B If this is not successful please contact the customer service.
Cleaning
Clean the chain saw thoroughly after each application so that
the faultless function is kept.
B Clean the case with a soft brush or a dry cloth.
Water, solvents and polishing agents shall not be
applied.
B Pay attention to that the ventilation slots for the motor
cooling are free (risk of overheating).
B In case of harder pollution or resins put the chain for some
hours in a container with chain cleaner. Afterwards wash up
the chain with clear water.
B Remove all adhering substances with a brush from the chain
wheel (13) and the sword fastening.
B Clean the oil flow canal (14) with a clean cloth.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika KSL2401-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika KSL2401-40 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info