520145

Atika KSL2401-40 Manual

23
Zoom out
Zoom in
Previous page
1/148
Next page
22
C
C
o
o
m
m
m
m
i
i
s
s
s
s
i
i
o
o
n
n
i
i
n
n
g
g
L Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the saw to the
relevant and properly earthed plug.
L Use a shockproof plug, mains voltage 230 V with
residual current circuit breaker (FI switch 30 mA).
Only use connection cables with sufficient diameters.
Switching On / Off
Do not use a device where
− the contactor can not be switched on and off.
− the chain and motor brake does not work properly
Damaged switches must be repaired or replaced
immediately by the customer service.
When switching on the chain saw must be supported and held
safely. Chain and guide bar must stand free.
B
Release the chain brake. Push the front hand guard (3)
towards the front handle (Pos. 1). The chain saw is ready for
operation.
Switch on
B Push and hold automatic trip switch (5). Then operate
the On/Off switch (6). Release now automatic trip switch.
Switching off
B Release On/Off switch (6).
Chain brake
The chain brake is a protective mechanism which in case
of a stroke back chain saw is initiated via the front hand
protection or after releasing the on/off switch. The saw
chain stops immediately (< 0,1 sec.).
Checking of chain brake
Check the chain brake’s proper function before each work start.
• Start the engine.
• Hold the chain saw with both hands and allow the engine to
run.
Â
Use the back of your hand to press against the front
hand guard.
The chain saw must stop immediately.
It is not allowed to use this chain saw without
properly working chain brake. Please contact the
manufacturer or the customer service point.
Clamping of saw chain
• Before setting or checking the saw chain tension pull
out power plug.
• In order to avoid injuries wear protective gloves.
Check the saw chain tension before
B start of work
B after the first steps
B during sawing regularly all 10 minutes
Only with a correct clamped saw chain and a sufficient
lubrication you can influence the durability.
L Please observe the following:
B a new saw chain must be reclamped more often until it has
elongated.
B in case of heating of chain to operating temperature it
expands and needs to be reclamped.
After finishing the sawing works release tension of saw
chain as in case of cooling too high tensions would emerge
in the saw chain.
B if chain flackers or comes out of the guide clamp it again
immediately.
Clamping of saw chain:
B Loosen the fastening screw (11) 1 – 2 revolutions anti-
clockwise.
B Turn the chain tension ring (12) stepwise clockwise until the
correct chain tension is reached. The engaging effect
prevents that the chain tension loosens.
L The fastening screw (11) turns with it; possibly it must
be released again during the clamping process.
B
The saw chain is correctly clamped when it can be lifted
in the centre of the guide bar by appr. 3 – 4 mm.
B Turn the chain tension ring (12) anti-clockwise when the saw
chain is clamped to much.
B Refasten the fastening screw with the hand.
B Check wether the chain links are positioned correctly in the
guide slot of the guide bar.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
c
c
h
h
a
a
i
i
n
n
s
s
a
a
w
w
Additional advices for sawing trunks
Never put the trunk for sawing on the ground. Support the
trunk in such manner that the cut does not close and the
saw chain jams. Use a safe base (e.g. sawhorse). Avoid
contact to ground with the guide bar tip or saw chain.
Adapt shorter trunks before sawing and clamp them firmly.
Avoid cutting of thin bosk and lumber. The chain saw is not
suitable for those works.
Carry out longitudinal cuts with special care as the claw
stopper is not used. Avoid saw backstroke by guiding the
saw with a small angle.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika KSL2401-40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika KSL2401-40 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info