520692

Atika GTC 230-18 Manual

19
Zoom out
Zoom in
Previous page
1/118
Next page
18
 Hold the machine with both hands.
Â
Press the trip switch (12) and then the ON/OFF switch
(13). While working, you can release the locking knob (6).
L
To protect the battery the machine automatically
switches off at a low battery.
Do not continue to operate the ON/OFF switch. Oth-
erwise the battery may be damaged.
Charge the lithium ion battery (Â „Charging the battery“).
S
S
w
w
i
i
t
t
c
c
h
h
i
i
n
n
g
g
o
o
f
f
f
f
 Release the ON/OFF switch button (13).
The cutting thread is after-running once the lawn trimmer
has been powered off. Therefore wait until the thread is
stationary before you restart the product.
R
R
e
e
m
m
o
o
v
v
i
i
n
n
g
g
t
t
h
h
e
e
b
b
a
a
t
t
t
t
e
e
r
r
y
y
 To remove the battery press the battery release button
(C).
W
W
o
o
r
r
k
k
i
i
n
n
s
s
t
t
r
r
u
u
c
c
t
t
i
i
o
o
n
n
s
s
You may not start to operate the machine until you have
read these operating instructions, observed all the in-
structions given and installed the machine as described!
Observe all safety instructions in any case.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
l
l
a
a
w
w
n
n
t
t
r
r
i
i
m
m
m
m
e
e
r
r
Correct working position
Before you start working it is recommended to adjust your lawn
trimmer so that you can work safely and comfortably.
Telescopic tube
The telescopic tube allows you to vary the working height.
1. For this, slightly loosen the clamping nut (14) and adjust
the length.
2.
Then, retighten the clamping nut (14).
Guide handle
 For better control, grasp the machine also at the front
handle (6).
Trimming
While trimming keep the lawn trimmer away from your body at a
sufficient distance. Tilt the product slightly forward and move it
from left to right.
It is recommended to cut higher grass above 15 cm in several
passes.
Guide the product around trees and shrubs so that the plants
are not damaged. Use the protective bow for better control.
Caution! Damaged plants may die off.
Do not guide the cutting thread directly at walls and paving
stones. Otherwise it will prematurely wear off.
Thread follow-up
During trimming, the cutting thread wears (becomes shorter) or
it may tear off so that it can no longer cut grass.
Shortly press the running lawn trimmer against firm ground.
This will extend the cutting thread (15) (by approx. 4 cm). If the
cutting thread exceeds the maximum cutting diameter it will be
shortened by the integrated knife within the protective hood.
V
V
i
i
b
b
r
r
a
a
t
t
i
i
o
o
n
n
s
s
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous system or
to blood vessels may occur.
You can reduce vibrations:
- by thick and warm working gloves,
- shorter working time (have longer breaks).
See a doctor if your fingers swell, you don’t feel well or your
fingers become numb.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning
work
− switch off device
− wait until the cutting thread is
stationary.
− remove the battery
− wear protective gloves.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
The cutting tool will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the product carry out
the following maintainance works regularly.
Check the machine for obvious defects such as
− worn or damaged components
− correct assembly and faultless covers and protective
devices.
Necessary repair works or maintainance have to be carried
out before using the power tool.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika GTC 230-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika GTC 230-18 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 3,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info