519989

Atika ELB 52 Manual

21
Zoom out
Zoom in
Previous page
1/170
Next page
20
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning work
− Stop the engine.
− Wait until the cutting device does not longer
move.
− Remove the spark plug connector.
− Wear protective gloves in order to avoid injury to
the hands.
− Do not carry out maintenance work close to
open flames. Risk of fire.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Only use genuine spare parts. Other than genuine parts may
result in unpredictable damages and injury.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
The tool will not come to a standstill immediately after cut-off.
Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the product
carry out the following maintainance works regularly.
Check the device for obvious defects such as
− loose fastening elements
− worn or damaged components
− correctly assembled and faultless covers and protective
devices.
Necessary repair works or maintainance have to be carried
out before using the machine.
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
t
t
h
h
e
e
a
a
i
i
r
r
f
f
i
i
l
l
t
t
e
e
r
r
Clean the air filter from dust and dirt on a regular basis to
prevent
− starting problems
− loss of output,
− too high fuel consumption.
Clean the air filter every 8 operating hours, or more frequently
in dusty environments.
Â
Put the choke lever to the position OFF to prevent dirt
from entering the carburetor.
Â
Remove the screw from the air filter housing (15) and
remove the air filter housing.
Â
Remove the air filter cover (36).
 Remove the air filter (16).
 Wash the air filter in a luke warm soapy solution.
Do not puff/blow out dirt particles, otherwise there is a
risk of eye injury.
 Allow the air filter to dry well and reinsert it.
L Damaged air filters must be replaced without delay.
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
/
/
r
r
e
e
p
p
l
l
a
a
c
c
i
i
n
n
g
g
t
t
h
h
e
e
f
f
u
u
e
e
l
l
f
f
i
i
l
l
t
t
e
e
r
r
Check the fuel filter if required. A contaminated fuel filter
restricts the fuel supply.
Â
Open the tank cap (20) and pull the fuel filter (21)
through the opening using a wire hook.
⇒ Slight contamination:
Pull the fuel filter from the fuel line and clean it in petroleum
ether.
⇒ Bad contamination:
Replace the fuel filter.
C
C
h
h
e
e
c
c
k
k
i
i
n
n
g
g
/
/
r
r
e
e
p
p
l
l
a
a
c
c
i
i
n
n
g
g
t
t
h
h
e
e
s
s
p
p
a
a
r
r
k
k
p
p
l
l
u
u
g
g
- Do not touch the spark plug or the spark plug
connector while the engine is running. High voltage!
- Risk of burning on the hot engine.
- Wear protective gloves.
Check the spark plug and the spark gap on a regular basis. For
this proceed as follows:
Allow the engine to cool down.
Â
Pull the spark plug connector (17) from the spark plug
(18).
 Remove the spark plug using the supplied spark plug
socket spanner (23).
The spark gap must be 0.6 to 0.7 mm.
 Clean the spark plug when it is contaminated.
Install the spark plug in reverse order.
Do not overtighten the spark plug.
Replace the spark plug:
- every 100 hours or each season (whichever case comes first)
- when the insulating body is damaged,
- when the electrodes show excessive erosion,
- when the electrodes show excessive dirt or oil.
Use the following spark plug type:
Torch L8RTC, NGK-BPMR 7 A, BOSCH WSR6F,
OREGON O-PR15Y, Champion RCJ 6Y
C
C
h
h
e
e
c
c
k
k
i
i
n
n
g
g
t
t
h
h
e
e
i
i
g
g
n
n
i
i
t
t
i
i
o
o
n
n
s
s
p
p
a
a
r
r
k
k
 Remove the spark plug (18).
Firmly connect the spark plug connector (17).
Â
Use an insulated pair of tongs to press the spark plug
against the engine body (away from the spark plug hole).
 Put the ON/OFF switch to the position
.
Pull the cranking rope.
L If there is no spark visible between the electrodes, the
spark plug may be defective.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ELB 52 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ELB 52 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish as an attachment in your email.

The manual is 3,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atika ELB 52

Atika ELB 52 Installation Guide - English, German, Dutch, Danish, French, Italian, Polish - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info