520782

Atika DK400 Manual

20
Zoom out
Zoom in
Previous page
1/99
Next page
19
Make a test cut when accuracy work is required and adjust
the grade again as the case may be.
Inner Cuts
The motor must be switched off.
Carrying out inner cuts
1. Remove the saw blade as described under Saw blade
exchange (page 18).
2. Bore a hole into the work piece to be handled (app.
Ø 6 - 7 mm).
3. Put the work piece with the bore hole over the access hole of
the saw table.
4. Guide the saw blade through the bore hole and insert it at
the top and the bottom in the saw blade mounting and clamp
it.
5. After the inner cut take out the saw blade as described under
Saw blade exchange.
Inserting coping saw blades
Coping saw blades can also be inserted in the saw with the help
of two adapters.
Before replacing the saw blade remove the
plug from the mains.
Do not use any cracked saw blades or those that have
changed their shape
Only use well-sharpened saw blades
Inserting coping saw blades, page 4 (fig. G, H, I)
1. Take out the saw blade as described under saw blade
exchange (page 18).
2. Take out the table insert (17) (fig. I).
3. Screw the saw blade in the adapters with the help of the
socket wrench delivered with (21).
4. Then, plug in the adapters in the saw blade mounting at the
top and the bottom (9 and 10, see fig. H, I).
5. Insert the table insert as shown in fig. I, Position C.
Working instructions
Before commencing work, ensure the following:
Saw blade protection and saw blade o. k.?
Saw blade sharp?
Workplace tidied?
You may not start to operate the machine until you have
read these operating instructions, observed all the
instructions given and installed the machine as described!
Also, note the following important points:
Place yourself outside of the area of danger
Take down the saw blade protection
- in case of breaks or when leaving the saw on the saw table
- when working on the workpiece
Place your hands flat on the workpiece with fingers closed.
With it, lead the work piece with the hand only up to the
leading edge of the saw blade protection.
Never remove loose splinters, chips, or similar by hand.
Ensure that you always comply with the safety
instructions given on p. 16 ff.
Maintenance and Care
Remove the plug from the power socket
before starting any maintenance or
cleaning work.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
L
Observe the following to maintain the functionality of the
saw.
Remove the sawdust from the inside of the saw. Therefore,
screw off the side covering (6) and exhaust or brush off the
sawdust.
Clean or exhaust respectively the cooling openings of the
motor after each operation.
Clean and oil all moving parts regularly.
L
Never use any grease!
Use for instance sewing machine oil, liquid hydraulic fluid
or environmentally acceptable spray oil.
Ensure that the saw blade remains free of rust and resin
Remove all resin residues from the saw bench top
The saw blade is a wearing part and becomes blunt after
long or frequent use
renew then the saw blade
Transport
Remove the mains plug before each
transport.
L
Transport the saw only with hinged down protection cover.
This will avoid possible injury from the saw blade.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika DK400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika DK400 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info