520782

Atika DK400 Manual

19
Zoom out
Zoom in
Previous page
1/99
Next page
18
the assembly are not contained in the scope of delivery. Use
therefore:
Description Quantity
Hexagon nut M 8 4
Gasket Ø 8mm
4
Washer Ø 8mm
4
Hexagon nut M 8, self-locking 4
Additionally we recommend a foam rubber base for the
reduction of vibrations and noise. It is not contained in the scope
of delivery.
Place the saw in a place that fulfils the following conditions:
secured against slipping
free of vibrations
even
free of tripping hazards
adequate light
Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables
− die Sägeblattschutz auf ordnungsgemäßen Zustand
− that the saw blade is in a perfect condition
Do not use any cracked saw blades or those that have
changed their shape.
Commissioning
Mains connection
Compare the voltage given on the machine model plate e.g. 230
V with the mains voltage and connect the saw to the relevant
and properly earthed plug
L
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and 10 A inert fuses.
Use connection cable or extension cable respectively with a
cross section of at least 1 mm².
Switch on
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired or
replaced immediately by the customer service.
Press the green button ( I ) on
the switch.
L
If there is a power cut, the
machine switches off automati-
cally. To switch on again, first
press the red and then the green
button.
Switching off
Press the red button ( 0 ) on the switch.
Adjusting the saw
Replacing the saw blade
Before replacing the saw blade remove the
plug from the mains.
Do not use any cracked saw blades or those that have
changed their shape
Only use well-sharpened saw blades
Replacing the saw blade, page 2 (fig. A and B) and
page 3 (fig. F)
Saw blade exchange
1. Turn adjusting knob to the left to release the saw blade.
2. Screw off the side covering.
3. Push down the upper saw blade mounting (10) and pull out
the saw blade.
4. Then take out the saw blade out of the lower saw blade
mounting (11) and pull through the table insert (18).
5. Fit in the new saw blade in reverse order.
Insert the saw blade always in that way that the teeth
show in direction of the saw table.
6. Clamp the saw blade by turning the adjusting knob.
Also saw blades without adapter can be inserted in the saw.
Therefore, it must be provided with a gudgeon at the top and at
the bottom. The saw blade can be inserted in two directions
(fig. J, page 4)
Slot a: For longitudinal sections
Slot b: For transverse sections
Adjust pitch
The table insert must not be set to the inclined position
when the blade is turning. The motor must be switched
off first.
Adjusting between 0° - 45°, page 4 (K)
1. Release the set screw (2).
2. Incline the saw table to the left until the required angle is
indicated on the angle scale (3) (0° - 45°).
3. Tighten the set screw (32 again to fix the adjusted angle.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika DK400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika DK400 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info