520796
12
Zoom out
Zoom in
Previous page
1/80
Next page
12
Assembling the saw blade casing and saw blade
E1 Release the locking nut (17) and pull off the flange (14 / 16).
E2 Insert the screws through the hole of the saw blade casing
(13). Afterwards, attach washers on the screws.
E3 E4 E5 Mount the saw blade casing (13). Fasten the casing with
washers and nuts.
E6 E7 Insert the saw blade cover (7) in the guide of the jigging
device and secure it using the screws.
E8 E9 E10 Fasten the guide (d) of the saw blade cover.
Tighten the screw only by hand and then slacken the nuts by
a half turn. The guide must move freely.
E11 Slide the saw blade flange (16) on the motor shaft.
E12 Danger of cutting! Wear gloves.
Mount the saw blade.
L Pay attention to the saw blade’s sense of rotation
(note the arrow on the saw blade and on the saw blade
casing).
E13 E14 Slide the saw blade flange (14) and the washer on the motor
shaft . Secure these parts using the locking nut (17).
E15 E16 E17 Mount the cover (18).
Assembling the handles
F Screw the handles (19) on the jigging device.
Assembling the support extension
G1 Insert the support extension (20) into the jigging device. Secure the
support extension with the star grip knob (21).
G2 Fasten the chain (8) onto the support extension.
Assembling the length stop
H Insert the length stop into the jigging device. Secure the length stop
with the star grip knob (21).
Before the first start-up
L
To achieve flawless functioning of the machine, please follow the
instructions listed:
Place the saw at a location which meets following conditions:
outdoor
secured against slipping
free of vibrations
even
free of tripping hazards
adequate light
To ensure a safer foothold when working with the saw secure the saw
against rolling away.
Before each use, check
connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
that the plastics insert is in a proper condition
the saw blade for flawless condition
the functioning of the jigging device
Do not use any cracked saw blades or such that have changed their
shape.
Do not use any saw blades made of HSS steel.
Immediately replace a worn or damaged plastics inserts.
Assume the correct work posture. Stand in front of the operating side
frontally to the saw blade line.
Start-up
Rotational direction of the saw blade
L
Ensure that the rotational direction of the saw blade is the same as
the rotational direction given on the saw blade casing (13).
Selection of saw blades
Consider when selecting the saw blade, that no edgeless or damaged saw
blades are used and that the diameter of the blade location hole is 30 mm
(note the nameplate on the machine).
L Mains connection
Compare the voltage given on the machine model plate e.g. 230 V with the
mains voltage and connect the machine to the relevant and properly earthed
plug.
L Use a shockproof plug, mains voltage 230 V with residual current
circuit breaker (FI switch 30 mA).
L Main fuse: 16 A inert
On/Off switch
Do not use any device where the switch can not be switched on and off.
Damaged switches must be repaired or replaced immediately by the
customer service.
Characteristic data of noise
Press the green button ( I ) on the switch.
L
If there is a power cut, the machine switches
off automatically. Push the green ( I ) button
to start the machine again.
Switching off
Press the red button (O) or the red button of the yellow switch
cover.
The built-in motor brake will decelerate the saw blade up to the
dead stop within 10 seconds.
The saw must not be used if the brake is defective, i.e. if the time
up to the saw blade’s dead stop exceeds 10 seconds.
Motor guard
The motor is equipped with a guard switch and it switches off
automatically when overload. The motor can be switched on again
after a cooling-down period (approx. 5 – 10 mins.).
Working with the saw
Before starting to work consider the following safety advices to keep the
risk of injuries as small as possible.
Saw blade, plastics inserts and recuperating spring o. k.?
Workplace tidied?
You may not start to operate the machine until you have read these
operating instructions, observed all the instructions given and installed
the machine as described!
Before making adjustments to the saw settings (e.g. replacing the saw
blade etc.)
switch off device
wait for standstill of the saw blade.
pull out power plug
Also, note the following important points:
Place yourself outside of the area of danger.
Place the wood piece in the jigging device. Cut through the piece with
uniform pressure.
Never remove loose splinters, chips, or similar by hand.
At any case pay attention to all safety instructions.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BWS 400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BWS 400 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info