520775

Atika BTU450 Manual

14
Zoom out
Zoom in
Previous page
1/92
Next page
13
Do not overload the machine! You work better and safer in the given
performance range.
The circular saw must only be operated with all the correctly mounted
guards.
The supplied splitting wedge must be used. Fig. 13 shows how the
splitting wedge is inserted and reset.
Replace the bench insert if the sawing gap is worn.
Do not use any cracked saw blades or such that have changed their
shape.
Use only well sharpened saw blades as edgeless saw blades increase
not only the risk of backstrokes but also charge the motor.
Do not use saw blades made of high speed steel (HSS) since this steel is
hard and brittle; use only tools according to EN 847-1.
The use of other tools and other accessories can signify a risk of
injury for you.
Pay attention that the saw blade conforms to the dimensions specified
under "Selection of saw blades" and is suitable for the work piece
material.
Only saw one work piece at a time. Never saw several work pieces at the
same time or do not bundle several individual pieces together for cutting.
There is danger that individual pieces may be caught by the saw blade in
an uncontrolled manner.
Ensure that cut off pieces are not caught up by the saw blade and
projected away
Do not use the saw for unsuitable purposes (see “Normal intended use”).
Remove all nails and metallic objects from the work piece before sawing.
Pay attention that the work piece does not contain any cables, ropes,
cords or the like.
Only cut work pieces with dimensions that allow secure holding while
sawing.
Only wood up to a thickness of 15cm is allowed to be cut with this
machine.
When cross cutting round wood it is required to secure the work piece
against turning using a pattern or holding device. Use a saw blade that is
suited for cross cutting.
Use a pushing stick when rip sawing narrow workpieces (space between
saw blade and rip fence less than 120 mm).
Always keep sufficient distance to the saw blade. Maintain sufficient
distance from driven components during operation.
The saw blade runs after. Wait until the saw blade has come to a
standstill before remove splinters, chips and waste.
Do not slow the saw blade down by applying lateral pressure to it.
Do not remove splinters, shavings and waste with your hands from the
dangerous area of the saw blade.
Remove cutting waste from the machine (as required) to prevent any
safety impairment at the workplace. This also applies to sawdust. Keep
the chip clearance free.
Switch the machine off and remove the mains plug from the socket when
− carrying out repair works
− maintenance and cleaning
− removal of faults (this also includes the removal of jammed splinters)
− checks of connecting lines, whether these are knotted or damaged
− transporting the saw
− changing the saw blade
− leaving the saw (also for short-term interruption)
Maintain your saw with care:
− Keep your tools sharp and clean in order to be able to work better
and safer.
− Follow the maintenance instructions and the instructions for tool
exchange.
− Keep handles dry and free of oil and grease.
Check the machine for possible damage:
− Before further use of the machine the protection devices or slightly
damaged parts must be checked carefully for their proper and
intended function.
− Check whether the movable parts function perfectly and do not stick
or whether the parts are damaged. All parts must be correctly
installed and fulfil all conditions to ensure perfect operation of the
saw.
− Damaged guards and parts must be properly repaired or exchanged
by a recognized, specialist workshop; insofar as nothing else is
stated in the instructions for use.
− Damaged or illegible safety labels should be replaced immediately.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and adjusting tools are
removed.
Store unused equipment in a dry, locked place out of the reach of
children.
Electrical safety
Design of the connection cable according to IEC 60 245 (H 07 RN-F) with
a core cross-section of at least
− 1.5 mm² for cable lengths up to 25 m
− 2.5 mm² for cable lengths over 25m
Long and thin connection lines result in a potential drop. The motor does
not reach any longer its maximal power; the function of the device is
reduced.
Plugs and coupler outlets on connection cables must be made of rubber,
plasticised PVC or other thermoplastic material of same mechanical
stability or be covered with this material.
Protect yourself against an electric shock. Avoid touching earthed parts
with your body.
The connector of the connection cable must be splash-proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant. Protect the
cable against heat, oil and sharp edges. Do not use the cable to pull the
plug from the socket.
Regularly check the saw cable and if damaged, have it renewed by a
recognised skilled electrician.
When running the connection line observe that it does not interfere, is not
squeezed, bended and the plug connection does not get wet.
Regularly check the extension cables and replace them if they are
damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especially approved
and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit breaker (30
mA).
The electrical connection or repairs to electrical parts of the machine
must be carried out by a certified electrician or one of our customer
service points. Local regulations – especially regarding protective
measures – must be observed.
Repairs to other parts of the machine must be carried out by the
manufacturer or one of his customer service points.
Use only original spare parts. Accidents can arise for the user through the
use of other spare parts. The manufacturer is not liable for any damage
or injury resulting from such action.
Before the first start-up
L
To achieve flawless functioning of the machine, please follow the
instructions listed:
Place the saw at a location which meets following conditions:
− outdoor
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BTU450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BTU450 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info