519915

Atika BTH Manual

19
Zoom out
Zoom in
Previous page
1/100
Next page
18
Maintenance and cleaning
Before each maintenance and cleaning work
− Switch off device
− Wait unitl the saw blade comes to a stop.
− Pull out power plug
Maintenance and repair work other than those described in this chapter is
only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must unconditionally
be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected damages and
injuries.
Cleaning
L Observe the following to maintain the operability of the machine:
Do not wash down device with water.
Remove shavings and dust only with a brush or vacuum cleaner.
Regularly clean and oil all movable parts (e.g. fasteners of the guard).
Fig. 10
L Never use any grease!
Use for instance sewing machine oil, liquid hydraulic fluid or
environmentally acceptable spray oil.
Take care that the saw blade remain free of rust and resin.
Resin residues must be removed from the table board.
L Resin residues can be removed with a commercial maintenance
and care spray.
The saw blade is a wearing part and will become dull after prolonged or
frequent use.
Renew the saw blade or have it sharpened.
Maintenance
Changing the saw blade
Remove the mains plug before changing the saw
blade.
Danger of cutting! The saw blade is massive and it could be to slick.
Wear gloves when replacing the saw blade.
Do not use any saw blades made of HSS steel.
Do not use any cracked saw blades or such that have changed their
shape.
Saw blades the body of which is broken must be discarded (no repair
allowed).
Only use well-sharpened saw blades.
Regrinding (sharpening) of saw blades is only allowed to be done by
qualified personnel. In particular note the following: Make sure that the
requirements for balancing of the tools according to EN 847-
1:2005+A1:2007 6.2.3.2 are met.
Danger of burning! The saw blade is still hot shortly after cutting.
1. Fold the safety guard backwards.
2. Loosen the screws of the table insert and move it back.
3. Insert rod (31) into motor-shaft and unscrew bolt ( left-hand-thread)
4. Now, the front saw blade flange (25) and the saw blade (24) can be
removed.
5. L Clean the saw blade flanges.
6. Install a new or sharpened saw blade.
L Pay attention to the correct running direction of the saw blade: The
arrow on the saw blade and the arrow on the protective cover must point
in the same direction!
7. Position the front saw blade flange again.
8. Re-tighten the clamping nut (26).
9. Secure the table insert.
10. Fold the safety guard back to its original position.
Replacing the table insert (Fig. 13)
Disconnect the mains plug before changing the
table insert.
Immediately replace a worn or damaged table insert.
1. Fold back the safety guard (14).
2. Loosen the screws of the table insert (5) and move it back.
3. Remove the 2 nuts (E) and remove the blade guard (11) together with the
safety guard.
4. Install a new table insert (5).
5. Secure the blade guard with the safety guard (for blade guard adjustment
see figure 15).
6. Secure the table insert.
7. Fold the safety guard back to its original position.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BTH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BTH in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info