519910

Atika BTA 90 Manual

37
Zoom out
Zoom in
Previous page
1/44
Next page
37
Abb. 58 33
Abb. 59
Abb. 60
•
Für noch sichereren Stand: (als Bodenbefestigung)
Sonderzubehör Winkelset Best.-Nr.:362510
•
For an even firmer stand:
Special accessory angle set, article no. 362510
•
Pour un positionnement plus sûr, utiliser le set de cales de la
gamme d’accessoires.
Réf. de commande: 362510
• Voor een nog veiliger stand:
Extra accessoires hoekset, bestelnr. 362510
•
För en stadig position:
Special-tillbehör vinkelsats, best.-nr. 362510
•
Benutzung des Schiebestockes bei schmalen Werkstücken
(Breite kleiner als 120 mm)
Verwenden Sie bei sehr flachen und schmalen Werkstücken
die niedrige Führungsfläche des Anschlages 33
•
Use the push stick for narrow workpieces (width less than 120
mm)
For very flat and narrow workpieces, use the low guide sur-
face of stopper 33
• En présence de pièces étroites (largeur inférieure à 120 mm) ,
utilisez le pièce de poussée
En présence de pièces extrêmement plates et étroites, utili-
sez la surface de guidage basse de la butée 33
•
Gebruik de schuifstok bij smalle werkstukken (breedte minder
dan 120 mm)
Gebruik bij zeer vlakke en smalle werkstukken het lage
geleidingsvlak van de aanslag 33
•
Använd matningspinne om du bearbetar smala arbetsstycken
(mindre än 120 mm breda)
Om du bearbetar mycket flata och smala arbetsstycken bör
du använda den låga styrytan på anslag 33
•
Keile schneiden mit dem Keilschneidanschlag
•
Cutting wedges with the wedge cutter
•
Coupez les cales en vous servant de la butée de coupe à onglet
•
Spieën snijden met de spiesnijaanslag
•
Såga kilar med hjälp av kilanslaget
•
Verdeckte Schnitte: Verwenden Sie einen Normspaltkeil nach
DIN 38 820 (Zubehör - Bestell-Nr. 360115)
Einstellung: Spitze ca. 2 mm unter höchster Sägezahnspitze,
Abstand 3-8 mm
Montieren Sie danach wieder die kpl. Schutzhaube
•
Concealed cuts: Use a normal splitting wedge in conformity with
DIN 38 820 (accessory - article no. 360115).
Setting: tip approx. 2mm below the highest saw tooth tip. Clear-
ance 3-8 mm
Then mount the complete protective guard again.
•
Coupe à couvert: Employer un coin à refendre normalisé selon
DIN 38 820 (accessoire - réf. de commande 360115)
Réglage: pointe à 2mm env. en dessous de la pointe de dent de
scie la plus élevée,
distance 3 à 8 mm
Après quoi, remontez le capot de protection complet
•
Bedekte sneden: Gebruiken van een standaard splijtwig
volgens DIN 38 820 (accessoires - bestell.-nr. 360115)
Instelling: punt ca. 2 mm onder hoogste zaagtandpunt, afstand
3 – 8 mm
Monteer daarna weer de complete beschermkap
•
Dolda snitt: använd en normalskiljekil enligt DIN 38 820
(tillbehör - best.-nr. 360115)
Inställning: Spetsen ca. 2 mm under den högsta
sågtandsspetsen,
stand 3 – 8 mm
Montera sedan den kompletta skyddshuven igen.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BTA 90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BTA 90 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info