701023
24
Zoom out
Zoom in
Previous page
1/146
Next page
24
Possible faults
Before each fault clearance
Switch off device
Wait for stop of saw
Pull out power plug
After each fault clearance, put into operation and recheck all security installations.
Fault Possible cause Removal
Machine fails to start after
switching on or switches off
during idle running
Power failure
Extension cable defect
Motor or switch defect
Doors not locked
Check safety fuse
Check cable, no longer use defect cable
Have motor or switch checked by an
approved electrician or replaced by original
spare parts
Close and lock the doors
Motor hums, but does not initiate
Condenser defect Condenser should be replaced by customer
service
Machine stops while cutting
Saw band edgeless
Feed too large
Replace saw band
Allow the motor to cool off and then continue
work using less pressure
Work piece jams when pushing
forward or pulling backward
Saw band edgeless
The parallel stopper is not parallel to the saw
band
Hold the work piece firmly and switch off the
motor immediately. Then renew the saw
band.
Readjust the parallel stopper.
Burn marks at the cut edges
Saw band is not suitable for the work step or
edgeless
Replace saw band
Saw band breaks
Wrong saw stressing
To high load
Wrong saw band
Adjust saw band stress
Reduce pressure against the saw band.
Wrong saw band
thin work piece = small saw band
thick work piece = broad saw band
Saw band contorted
To high lateral load Avoid lateral pressure on the saw band.
Saw band runs out of cutting line
or passes of
Saw band does not run centrally on the upper
band saw roll
Adjust incline of the upper band saw roll
Saw vibrates
Insufficient fixation
Saw table loose
Fixation screws of motor lose
Fix saw on suitable ground
Adjust and fix saw table
Fasten fixation screws
Sawdust exit blocked
No extraction system connected
Extraction power to weak
Switch off saw, remove sawdust and
connect extraction system
Switch off saw, remove sawdust and
increase extraction power (air speeds 20
m/sec on suction socket of sawdust.
Saw band does not move
although motor is running
Drive belt lose
Drive belt defect
Clamp drive belt
Replace drive belt
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika BS 205-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika BS 205-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Atika BS 205-2

Atika BS 205-2 Installation Guide - English, German, Dutch, Danish, French, Italian, Polish, Swedish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info