519909

Atika ATS 250 Manual

15
Zoom out
Zoom in
Previous page
1/80
Next page
13
Check the machine for possible damage
− Before continuing to use the machine, the protective
devices must be inspected to ensure that they work
perfectly and with their intended function
− Check whether the movable parts function perfectly and
do not stick or whether the parts are damaged, All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation of the saw
− Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Do not allow any tool key to be plugged in!
Store the unused machine in a dry locked place away from
the reach of children
Electrical safety
Design of the connection cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
2
for cable lengths up to 25m
2.5 mm
2
for cable lengths over 25m
Protect yourself against an electric shock. Avoid touching
earthed parts with your body.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the saw cable and if damaged, have it
renewed by a recognised skilled electrician.
Regularly check the extension cables and replace them if
they are damaged
Do not use any defective connection cables
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use
Do not set up any provisional electrical connections
Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician or
one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
Preparing for commissioning
L
To achieve perfect function of the machine, follow the
notes given in these instructions
You have to attach the following parts:
Protective guard, see P. 68
Transverse stop, longitudinal stop, see P. 13-14
Optional: - Stand, see P. 66-67
- Table width and length extension, see P. 70
Commissioning
• Place the saw in a place that fulfils the following conditions:
secured against slipping
free of vibrations
even
free of tripping hazards
adequate light
• Before each use, check
− Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables
− that the guard is in a proper condition
− the splitting wedge setting (see splitting wedge setting)
− that the saw blade is in a perfect condition
− whether the pushstick is to hand
• Do not use any cracked saw blades or those that have
changed their shape
• Do not use any saw blades made of HSS steel
• When sawing, place yourself to the side of the danger area
(saw blade)
• Lower the guard onto the bench top
− when working on the workpiece
− when interrupting the work or leaving the saw
Rotational direction of the saw blade
L
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the guard
(362706)
Mains connection
Compare the voltage given on the machine model plate e.g. 230
V with the mains voltage and connect the saw to the relevant
and properly earthed plug
L
Alternating current motor:
Use a shockproof plug, mains voltage 230 V with residual
current circuit breaker and 10 A inert fuses.
Use the connection or extension cable according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
2
for cable lengths
up to
25m
2.5 mm
2
for cable lengths
over
25m
Switch on
œ
by pressing the green, lower button on the switch.
L
If there is a power cut, the machine switches off
automatically. To switch on again, first press the red and
then the green button.
Switching off
œ
The saw can be switched off by pressing the upper, red
button of the switch, or pressing down the yellow-red flap
(this can be locked by means of a padlock).
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Atika ATS 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Atika ATS 250 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info