Manual Atika ASP 10-1350 (page 21 of 88) (English, German, Dutch, Danish, French, Polish, Swedish)

519272

Zoom out

Zoom in

1/88

 What type of logs can I split?

Size of logs

Length: max. 1350 mm

Diameter: min. 120 – max. 400 mm

The log diameter is a recommended guideline figure,

because:

− thin logs can be difficult to split if they contain knots or if

the fibres are too strong.

− logs with a diameter of over 400 mm can be split if the

fibres are smooth and open.

Do not try to split green logs. Dry logs are much easier to

split, and do not cause jams as often as green (damp) wood.

Operation

Two-hand operation

Never operate the log splitter with two people.

Never block the control handles (clamping claws).

1. Press the green switch on the electric motor. Wait a few

moments until the motor has reached its operating

revolutions and the required pressure has been built up in

the hydraulic pump.

L Check the direction of the motor in the log splitter

with threephase motor (400 V 3~), because operation in

the wrong direction damages the oil pump.

L At temperatures below –5° C, let the log splitter run

for at least 15 min. in neutral to heat up the oil.

2. Place the log on the log splitter table.

L Only split the logs in the direction of the wood fibres.

3. Hold the log tight with the clamping claws.

4. Press both operating handles down simultaneously:

Î The splitting blade falls down and splits the log.

5. Release the two control handles, the splitting blade

returns to its initial position.

L If you only release one control handle, then the

splitting blade remains where it is.

 Special instructions for splitting logs:

 Preparations:

The logs to be split should be cut to the maximum

dimensions. Ensure also that the logs are cut straight and

square.

Place the log properly on the log splitter, so as not to cause

any risk of stumbling or falling to the operator.

 Adjusting the stroke height

In case of shorter wood pieces the efficiency can be

increased by shortening the return of the splitting cutter.

1. Place the log on the

splitting table and

press the two control

handles to bring the

splitting blade down to

approx. 3 - 5 cm

above the log.

2. Release one control

handle so that the

blade stays in this

position.

3. Switch the machine

off and disconnect the

power.

4. Release the second control handle.

5. Shorten the return path at the rod fitted to the side by

fixing the holding screw at the necessary height.

Holding screw

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Atika ASP 10-1350 in the language / languages: English, German, Dutch, Danish, French, Polish, Swedish as an attachment in your email.

The manual is 5,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Atika ASP 10-1350 Manual

Product: