121861

ATAG WU 9011 GC Manual

11
Zoom out
Zoom in
Previous page
1/13
Next page
GENERAL
Carefully read the following important information regarding
installation safety and maintenance. Keep this information
booklet accessible for further consultations. The appliance has
been designed for use in the ducting version (air exhaust to
the outside – Fig.1B),  ltering version (air circulation on the
inside – Fig.1A) or with external motor (Fig.1C).
SAFETY PRECAUTION
1. Take care when the cooker hood is operating simultaneously
with an open  replace or burner that depend on the air in the
environment and are supplied by other than electrical energy,
as the cooker hood removes the air from the environment
which a burner or  replace need for combustion. The negative
pressure in the environment must not exceed 4Pa (4x10-5 bar).
Provide adequate ventilation in the environment for a safe
operation of the cooker hood. Follow the local laws applicable
for external air evacuation.
Before connecting the model to the electricity network:
- Control the data plate (positioned inside the appliance)
to ascertain that the voltage and power correspond to the
network and the socket is suitable. If in doubt ask a quali ed
electrician.
2. Warning !
In certain circumstances electrical appliances may be a
danger hazard.
A) Do not check the status of the  lters while the cooker
hood is operating
B) Do not touch bulbs or adjacent areas, during or straight
after prolonged use of the lighting installation.
C) Disconnect the electrical plug prior to any
maintenance.
D) This appliance is not intended for use by young children
or in rm persons without supervision
E) Young children should be supervised to ensure they do
not play with the appliance
F) There shall be adequate ventilation of the room when
the rangehood is used at the same time as appliances
burning gas or other fuels
G) There is a risk of  re if cleaning is not carried out in
accordance with the instructions
This appliance conforms to the European Directive, Waste
Electrical and Electronic Equipment (WEEE). By making sure
that this appliance is disposed of in a suitable manner, the user
is helping to prevent potential damage to the environment
or to public health.
The
symbol on the product or on the accompanying
paperwork indicates that the appliance should not be treated
as domestic waste, but should be delivered to a suitable
electric and electronic appliance recycling collection point.
Follow local guidelines when disposing of waste. For more
information on the treatment, re-use and recycling of this
product, please contact your local authority, domestic waste
collection service or the shop where the appliance was
purchased.
INSTALLATION INSTRUCTIONS
Assembly and electrical connections must be carried out
by specialised personnel.
• Electric Connection
The appliance has been manufactured as a class II, therefore
no earth cable is necessary.
The plug must be easily accessible after the installation of
the appliance.
• If the hob is electric, gas, or induction, the minimum distance
between the same and the lower part of the hood must be
at least 65 cm.
If a connection tube composed of two parts is used, the
upper part must be placed outside the lower part. Do not
connect the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes from other
appliances generated by other than an electrical source.
Before proceeding with the assembly operations, remove
the anti-grease  lter(s) (Fig.2) so that the unit is easier to
handle.
- In the case of assembly of the appliance in the suction version
prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which has
the same diameter as the air exhaust outlet hole. If a pipe
with a smaller diameter is used, the e ciency of the product
may be reduced and its operation may become noisier.
• Installation
The following instruction should be followed to carry out the
correct installation of the cooker hood.
1. Mounting of the cooker hood on the lower side of the
cupboard.
2. Selection of the version (extraction or  ltration)
3. Before starting to  x the hood, disconnect the anti-grease
lter for easier appliance handling:
- Open panel B as shown in Fig.2.
- Pull handle C as shown in Fig.3.
• Fitting the cooker hood into the lower part of the wall
cabinet
For all measurements relating to the cooker hood, please
refer to Fig.4.
Before  xing the cooker hood to the lower part of the cabinet,
the following steps should be performed:
1- Remove the 4 screws E xing the two cooker hood lamps H
(RHS and LHS) in place as indicated in Fig. 5A.
2- Remove the lamps H and disconnect the connectors W of
the halogen lamps to make installation easier, as indicated
in Fig. 5B.
3. Make sure the thickness of the cabinet falls within the range
of values listed in Fig. 5C.
Fit the cooker hood in the cabinet (Fig. 6) and make sure the
4 springs are  xed in place well.
Fix the cooker hood to the cabinet securely by using a
screwdriver to tighten the screws M until the appliance is
ush with the cabinet (Fig. 6).
4. Connect the connectors W of the halogen lamps again and
reinstall the lamps H xing them with the 4 screws E that were
previously removed.
ENGLISH
GB
- 12 -
… 11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG WU 9011 GC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG WU 9011 GC in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info