507741
7
Zoom out
Zoom in
Previous page
1/64
Next page
7
English
4. Installation Instructions
REMARK The water softener must be connected according to the local regulations. The
water softener must be equipped with a class CA security (check valve). The
check valve must be placed in the cold water conduits before the water
softener, and must be KIWA approved (by a third party). Also consult worksheet
VEWIN 4.6.
When you choose your softener location, please take into account the following parameters :
1) Install your ATAG Descale softener in a chosen place on a flat firm and clean surface. Your ATAG
Descale softener must be close to a drain line to allow an easy connection and check there is
an electrical earth grounded plug to power the unit.
2) During cold weather, it is recommended to bring your ATAG Descale softener back to room
temperature before operation. During hot weather, do not install your ATAG Descale softener in
direct sunlight or in a room with a temperature above 45°C
3) All plumbing for the water inlet, distribution and drain lines should be done correctly in
accordance with the legislation in force at the time of the installation. The pipe size for the drain
line should be a minimum of 20 mm (
3
/
4
’).
4) All the soldering on the main plumbing and to the drain line should be done before connecting the
ATAG Descale softener. Failing to do so can cause irreversible damage. For any maintenance,
shut down water inlet, unplug your ATAG Descale softener and open the taps at the top and at
the bottom of your house to drain your installation.
5) Manually add water in brine tank above the aircheck (around 10 liters). Do not fill with salt at the
moment.
6) Place your ATAG Descale softener in the by-pass position. Turn on the main water supply. Open
a cold soft water tap nearby and let run a few minutes or until your ATAG Descale softener is
free from any foreign material (usually solder) that may have resulted from the installation. Once
clean, close the water tap.
7) Switch on the power. Once plugged in the valve may do a cycle on its own in order to go to
the service position. Display will alternate between installer name, time of day, flow rate and
remaining capacity.
NORMAL OPERATION POSITION
Figure 1
DIAGNOSTIC POSITION
Figure 3
BYPASS POSITION
Figure 2
SHUT OFF POSITION
Figure 4
Bypass positioN
sUppLy WatER
ENtERs
UNtREatED WatER EXits
Atag Descale handl EN FR NE.indd 7 13/06/12 16:12
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ATAG Descale at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ATAG Descale in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of ATAG Descale

ATAG Descale User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info